Abstract:The strength and ductility of transition metallic element alloyed Al alloys could be inevitably and severely weakened if these elements appeared as coarse intermetallics. Present studies aimed to optimize the morphologies and sizes of these intermetallics via composition design and process selection so as to decrease their detrimental effects to the properties. It is shown that the dendritic α-Al(Fe,TM)Si phase solidified as primary phase can be refined into small dendrites or micro- and submicro-sized particles via controlling the cooling rate and alloy composition, and this phase exhibits better heat resistance. After spark plasma sintering (SPS) the atomized alloy powders, the bulk aluminum matrix composites (AMCs) were successfully prepared and well strengthened by the uniformly distributed particulate α-Al(Fe,TM)Si phase. These sintered bulk composites also possess good heat resistance that might facilitate their application for some heat-resistant parts. The transmission electron microscope (TEM) and high-resolution TEM (HRTEM) results indicate these α-Al(Fe,TM)Si phases possesses body-centered-cubic structure with a lattice constant of 1.25 to 1.27 nm. The solidification or phase formation of these alloys is discussed as well as the densification process for the SPS of powders. The present studies indicate a possibility to prepare in situ small dendritic/particulate α-Al(Fe,TM)Si phase reinforced AMCs by using the casting process and controlling the normal impurity elements in Al alloys.

Microstructure of in Situ Al3Ti/6351Al Composites Fabricated with Electromagnetic Stirring and Fluxes

In Situal3ti–al2o3 Intermetallic Matrix Composite: Synthesis, Microstructure, and Compressive Behavior

FLEXURAL STRENGTH OF IN-SITU REACTION PROCESSED Al2O3-Al3Ti-Al COMPOSITES

Evaluation of the microstructure of in-situ reaction processed Al3Ti-Al2O3-Al composite

Microstructure of in Situ Synthesized Al3ti/6063 under Combination of Magnetic Fields

In situ fabrication and microstructure of Al2O3 particles reinforced aluminum matrix composites

Preparation and Mechanical and Tribological Properties of A13Zr+6082Al Composites Fabricated by Magnetic Stirring in Situ

Microstructures Of Components Synthesized Via Electron Beam Selective Melting Using Blended Pre-Alloyed Powders Of Ti6al4v And Ti45al7nb

Effect of Ti Content and Stirring Time on Microstructure and Mechanical Behavior of Al-B4C Composites

In-situ Production and Microstructure of TiC/Fe3 Al Composites

Microstructure and Mechanical Properties of Al<sub>2</sub>O<sub>3</sub>/TiAl <i>In Situ</i> Composites Doped with Fe<sub>2</sub>O<sub>3</sub>

Preparation and mechanical and tribological properties of A1(3)Zr+6082Al composites fabricated by magnetic stirring in situ

In Situ Formation of Al3Ti and Its Effects on the Microstructure, Hardness and Tribological Properties of Al Matrix Composites with Various Ti Contents

Microstructure and mechanical properties of Al2O 3/TiAl in situ composites doped with Fe2O3

Preparation, Microstructure and Mechanical Properties of In-Situ TiC/Al–Si–Fe Aluminum Matrix Composites

Micro-/nano-scale structure and elemental diffusion in the Al/Ti/Al sandwich structure

Synthesis and Characterization of In Situ Dendritic/Particulate α-Al(Fe,TM)Si Phase Reinforced Al Matrix Composites

Microstructure and Mechanical Properties of Ti2AlC-reinforced TiAl Composites

Microstructural evolution caused by electromagnetic stirring in superheated AlSi7Mg alloys

Microstructure and Mechanical Properties of Al<sub>2</sub>O<sub>3</sub>/TiAl <i>in Situ</i> Composites Doped with Fe<sub>2</sub>O<sub>3</sub>

Microstructures and mechanical properties of in-situ TiB2/Al−xSi−0.3Mg composites