Abstract:This study investigates the substitution of cerium (Ce) with mischmetal (MM) in cast Al-MM alloys, focusing on microstructure, hardness, tensile and compression properties, creep resistance, and coarsening resistance. Al-MM alloys with various MM compositions (Ce, Ce-50La, Ce-33La, and Ce-27La-19Nd, weight percent) exhibit near-eutectic and hyper-eutectic microstructures for Al-9MM and Al-12MM compositions, respectively, with similar as-cast hardness (~525 MPa). All Al-9MM alloys show tensile yield stress ~55 MPa, ultimate tensile strength ~130 MPa, and fracture strain ~8%.The microstructural and mechanical properties consistency demonstrates the flexibility of MM compositions in Al-MM alloys. Al-9MM exhibits excellent coarsening resistance, with minimal hardness reduction when exposed to 300 and 350 C for up to 11 weeks, and a modest ~15% hardness reduction at 400 C for 8 weeks, outperforming eutectic Al-12.6Si and Al-6.4Ni alloys. Additionally, Al-9MM shows higher creep resistance at 300 C compared to most precipitate-strengthened Al-Sc-Zr and solid-solution-strengthened Al-Mg/Mn alloys, but is outperformed by eutectic-strengthened Al-6.4Ni and Al-10Ce-5Ni alloys.The effect of casting cooling rate is investigated through wedge casting: Al-9Ce transitions from hypo- to hyper-eutectic as cooling rates decrease, while Al-12Ce consistently shows hyper-eutectic microstructures. Al11Ce3 lamellae become finer and more closely spaced with increasing cooling rates. Al-9Ce maintains steady hardness at high to moderate cooling rates but shows reduced hardness at lower rates, whereas Al-12Ce shows no change in hardness.With a 15% reduction in energy consumption and CO2 emissions, Al-Ce alloys where Ce is replaced with MM offer comparable mechanical properties and enhanced environmental benefits, highlighting the potential of MM as a sustainable alternative.

Effect of Ce on Microstructure, Mechanical Properties and Corrosion Behavior of High-Pressure Die-Cast Mg–4Al-based Alloy

Tailoring the microstructure and enhancing the corrosion resistance of extruded dilute Mg-0.6Al-0.5Mn-0.25Ca alloy by adding trace Ce

Effect of Ce Addition on the Microstructure, Thermal Conductivity and Mechanical Properties of Mg–0.5Mn Alloys

Effect of Ce Addition on Modifying the Microstructure and Achieving a High Elongation with a Relatively High Strength of As-Extruded AZ80 Magnesium Alloy

Effect of Ce Content on the Microstructure and Mechanical Properties of Al-Cu-Li Alloy

Enhanced Mechanical Properties and Corrosion Resistance of Rolled Mg-1.5Sn-0.5Ca Alloy by Ce Microalloying

Effect of cerium alloying on microstructure, texture and mechanical properties of magnesium during cold-rolling process

Effect of Ce Addition on Microstructure, Thermal Conductivity, and Mechanical Properties of As-Cast and As-Extruded Mg–3Sn Alloys

Effect of CeLa addition on the mechanical properties of Al–Cu–Mn–Mg–Fe alloy

The effect of minor Ti and Mn additions on the microstructure and mechanical properties of additive manufactured Al–Ce–Mg alloys

Effect of rare earth Ce addition on microstructure and mechanical properties of titanium alloy Ti-6Al-4V

Achieving high strength-ductility synergy in dilute Mg-Al-Ca alloy by trace Ce addition

Influence of Introducing Zr, Ti, Nb and Ce Elements on Externally Solidified Crystals and Mechanical Properties of High-Pressure Die-Casting Al–Si Alloy

Microstructures, Mechanical Properties and Corrosion Resistances of Extruded Mg-Zn-Ca-Xce/La Alloys

Effect of Ce on microstructure and dynamic compression properties of ZK60 alloy

Effects of Mischmetal Composition and Cooling Rates on the Microstructure and Mechanical Properties of Al-(Ce, La, Nd) Eutectic Alloys

Towards reducing tension-compression yield and cyclic asymmetry in pure magnesium and magnesium-aluminum alloy with cerium addition

Effect of Sm and Ce content on microstructure and mechanical property of newly developed Mg-Sm-Ce-Mn based alloy

Influence of mixed rare earth elements(Y and Ce) on the microstructure and corrosion behaviour of Mg-4Al-3Ca alloy

Effect of Hot Forging Process Parameters and Ce Addition on the Microstructure and Mechanical Properties of an As‐Forged AZ80 Alloy

Effect of Ce on the localized corrosion behavior of non-equiatomic high-entropy alloy Fe40Mn20Cr20Ni20 in 0.5 M H2SO4 solution