Abstract:ZrB2-20vol% SiC-30vol% Zr–Al–C (ZSA) composite ceramics were fabricated by using graphite powders, SiC powders and ball milled Zr/Al/ZrB2 composite powders through spark plasma sintering. The ball milling process resulted in forming Zr/Al coating layer covered ZrB2 powders and introducing O into the composite powders despite of Ar protective atmosphere. The Zr/Al coating layer reacted with graphite powders to in situ form layered Zr–Al–C grains in ZSA composite ceramics during the sintering process. As increasing milling time longer than 1h, the great increase in the introduced O included by Zr/Al/ZrB2 composite powders leaded to an insufficiency in Al due to the formation of Al2O3, which resulted in a remarkable phase transition from Zr2Al4C5 to Zr3Al4C6 in the ZSA composite ceramics. The more sufficient mixing and combination of Zr, Al and ZrB2 achieved by increasing milling time leaded to the more uniform distribution and the longer slenderness ratio of Zr–Al–C grains in the ZSA composite ceramics, which made the major contribution to the toughening of ZSA composite ceramics. The optimal milling time for Zr/Al/ZrB2 composite powders was 4h and the corresponding ZSA composite ceramic showed the maximum value of fracture toughness, 5.96±0.41MPam1/2, which is about 15% higher than that of the ZSA ceramic sintered using un-milled powders. The longer milling time of 6h leaded to much more Al2O3 and few layered Zr–Al–C grains in the ZSA ceramic that exhibited the minimum fracture toughness. The fracture mode is a mixture of inter- and intra-granular fractures, and the toughening mechanisms are the crack deflection and crack bridging that result from the existed Zr–Al–C grains with laminated microstructure.

Preparation of Nano-Composite ZTM Ceramics of High Mechanical Properties by In-Situ Crystallization of Amorphous Bodies

Preparation And High-Temperature Strengthening Of Tetragonal Zirconia Mullite Whisker Composites

ZrSiO4 toughed Al2O3 ceramics prepared by reaction sintering

Reaction mechanisms and properties of in situ porous Al2O3-ZrO2-mullite composites

Preparation and Characterization of ZrB 2 -Sic Ultra-High Temperature Ceramics by Microwave Sintering

The Effect of Nano-Al<sub>2</sub>O<sub>3</sub> on Sintering Behavior and Mechanical Property of ZrO<sub>2</sub> Ceramics

Temperature‐dependent mechanical and oxidation behavior of in‐situ formed ZrN/ZrO2‐containing Si3N4‐based composite

Microstructure and mechanical properties of Zr3Al3C5-based ceramics synthesized by Al-Si melt infiltration

Fabrication, Microstructural Evolution, and Mechanical Properties of SiC/(Hf0.25Ta0.25Zr0.25Nb0.25)C/C Nanocomposites

The Effect of Nano-Al2O3 on Sintering Behavior and Mechanical Property of ZrO2 Ceramics

Microstructure and mechanical properties of dense ZTA ceramics with high Cr2O3 solution

Microstructures and Enhanced Mechanical Properties of (Zr, Ti)(C, N)-Based Nanocomposites Fabricated by Reactive Hot-Pressing at Low Temperature

Zirconia Toughened Alumina Ceramics via Forming Intragranular Structure

Microstructure, Mechanical, and Thermal Properties of in Situ-Synthesized (zrb2+sic)/zr2[al(si)]4c5 Composites

Microstructure and Mechanical Properties of Hot-Pressed Al2O3–mullite–ZrO2–SiC Composites

SiC and ZrN Nano-Particulate Reinforced AlON Composites: Preparation, Mechanical Properties and Toughening Mechanisms

Effects of zirconium source and content on zirconia crystal form, microstructure and mechanical properties of ZTM ceramics

Fabrication and Mechanical Properties of Homogeneous Zirconia Toughened Alumina Ceramics Via Cyclic Solution Infiltration and in Situ Precipitation

Effects of ZrB2 on Mechanical Properties of Al2O3-ZrB2-SiC Composite Ceramics at Room Temperature

Effect of ball milled Zr/Al/ZrB2 composite powders on microstructure and toughening of ZrB2–SiC/Zr–Al–C composite ceramics sintered by spark plasma sintering

Preparation and mechanical properties of mica glass-ceramic/Y-TZP composites