Abstract:Admixture and water-cement ratio are important factors affecting the development of properties of cement mortar or concrete. In order to study the influence of admixtures and water-cement ratio on the hydration products and the mechanical properties of cement-based materials, the study combined hydration reaction mechanism of pure cement and silicate admixture, derived the formulae of hydration products, theoretical maximum mixing amount and total porosity of composite cement-based materials, and investigated the effects of mixing amount of cement mortar with fly ash, steel slag and lithium slag on total porosity, mechanical properties and hydration products. This paper designed 3 gradients of water-cement ratio (0.50, 0.42 and 0.34), 3 kinds of admixtures (lithium slag, fly ash and steel slag) and 2 contents (20% and 60%); the ratio of cementitious material to sand was 1:2.5, and then, molding specimen accorded with the mix of mortar in the triple mold and the mechanical properties of mortar were tested when specimen was cured to 1, 3, 7, 28 and 90 d. The results showed that, after the same content of fly ash, steel slag and lithium slag incorporation, the contents of hydration products of composite cementitious materials, i.e. calcium hydroxide (CH) and calcium silicate hydrate (CSH), and the total porosity were smaller than those of pure cement; when the water-cement ratio decreased from 0.50 to 0.34, the total porosity of cement mortar decreased from 16.0% to 9.3%, and the contents of CH and CSH increased for the compound cement-based materials with mixing amount of 5%, but the increments were not big; the porosity of fly ash, steel slag and lithium slag cement-based composite materials reduced from 16.6%, 17.2% and 16.0% to 9.9%, 10.9% and 9.3%, respectively. When the admixture amount increased to 10%, the variation of porosity and hydration products of the 3 kinds of mortar was different. The content of hydration products (CH and CSH) of composite cementitious materials was still smaller than that of pure cement. Compared to pure cement, the contents of CH and CSH of lithium slag mortar reduced by about 81.1% and 4.2%, fly ash mortar reduced by about 20.9% and 9.5%, and steel slag mortar reduced by approximately 3.0% and 9.5%, respectively. The porosity of lithium slag, fly ash and steel slag mortar increased by 0.1%, 3.6% and 7.6%, respectively. Among the 3 kinds of admixtures, the theoretical maximum mixing amount of fly ash was the maximum, followed by lithium slag, and the steel slag’s theoretical maximum mixing amount was the minimum. It was found that the compressive strength of lithium slag cement-based composite material was prior to fly ash and steel slag cement-based composite materials. In early stage (14 days ago), the compressive strength of fly ash mortar was prior to steel slag mortar; when water-cement ratio was relatively high, the compressive strength of steel slag mortar was close to fly ash. When the mixing amount was 20%, the compressive strength of lithium slag cement mortar was prior to pure cement mortar; if the mixing amount was 60%, the compressive strength of fly ash, steel slag and lithium slag mortar was worse than pure cement mortar. The study provides theoretical basis for material adding in mortar and concrete.

THE STRENGTH EFFECT OF MINERAL ADMIXTURE ON CEMENT CONCRETE

The Synergy Effect of Limestone Powder and Mineral Admixtures on the Mechanical Property of Mortar

High-Strength and Flowing Concrete with a Zeolitic Mineral Admixture

Experimental study on strength and abrasion-resistance enhancement admixture

Effects of Mineral Admixtures on Fatigue Behavior of Concrete

Effect of Mineral Admixture on Mechanical Properties of Concrete by Adjusting Interfacial Transition Zone Microstructure

Stuay of Mineral Admixtures as Fine Aggregate on Hydration Products and Spectral Performance of Mortar

Effect of mineral admixtures on the hydration heat of mortar in super high strength concrete

Mineral Admixtures Affecting the Performance of Lightweight High Strength Concrete

Effect of steel slag powder, fly ash, and silica fume on the mechanical properties and durability of cement mortar

Long-term strength and durability performance of eco-friendly concrete with supplementary cementitious materials

Strength, durability and appearance of low-carbon fair-faced concrete containing multiple mineral admixtures

Low-Field Nuclear Magnetic Resonance Investigation on Early Hydration Characterization of Cement Paste Mixed with Mineral Admixtures

Experimental Application of Mineral Admixtures in Lightweight Concrete with High Strength and Workability

Effects of calcium formate on early-age strength and microstructure of high-volume fly ash cement systems

Influence of Mineral Admixtures on the Performance of Polymer Modified Porous Concrete

Effect of Mineral Admixtures on the Structural Build-Up of Cement Paste

The role of fly ash microsphere in the microstructure and macroscopic properties of high-strength concrete

Influence of Mineral Admixtures on the Properties of Magnesium Oxychloride Cement Lean Concrete

Influence of admixture and water-cement ratio on hydration products and mechanical properties of cement-based materials