Abstract:The thermal and dimensional stability of epoxy resin(EP)in-situ modified by cyanate ester(CE)and polydimethylsiloxane (PDMS) are investigated by means of experiments and numerical simulation. Thermal gravimetric analysis(TGA)and differential scanning calorimeter(DSC)are used to analyze the heat resistance of the modified EP. The dimensional stability is characterized by the volume shrinkage of the series PDMS/CE/EP obtained by the density method. The chemical structure of the PDMS/CE/EP is analyzed by Fourier transform infrared spectroscopy(FTIR). The results of TGA and DSC indicate that the thermal stability of PDMS/CE/EP decreases firstly and then increases with the increase in the amount of CE. The addition of PDMS shows a slight effect on the thermal stability. The 40％ CE makes the blending system exhibit the lowest initial decomposition temperature,which reduces by 15.5％ and 40.8％ compared with pure EP and CE,respectively. The FTIR results suggested that the influence of CE on the thermal stability of the modified EP is mainly ascribed to the generation of oxazolidinone ring with low thermal stability and the increase in the triazine ring with high thermal stability. The volume shrinkage measurement results show that the introduction of CE and PDMS are both beneficial to the improvement of the dimensional stability of the blending systems. The in-situ addition of 80％ CE shows the lowest volume shrinkage of 6.11％. The thermal stress distribution of PDMS/CE/EP generated during the solidification process is simulated by the finite element analysis. The results suggested that the introduction of 80％ CE into EP results in the lowest thermal stress in the blending system,which indicates that the system has the lowest volume shrinkage,which agrees well with the experimental results.

Hygrothermal stability of dicyanate-novolac epoxy resin blends

Curing, Thermal Stability and Composite Properties for Blends of the Novel Bismaleimide and Cyanate Containing Naphthalene

Synthesis, Cure Kinetics and Thermal Properties of the 2,7-Dihydroxynaphthalene Dicyanate

Study on Co-curing Behavior and their Laminate Properties of Low Bromined Epoxy/Cyanate Blends

Cure and thermal properties of cyanate ester resin containing naphthalene ring

EFFECTS OF HYDROTHERMAL AGEING ON STRUCTURES AND PROPERTIES OF CYANATE/EPOXY NOVOLAC BLENDS

Thermal properties of an epoxy cresol-formaldehyde novolac/diaminodiphenyl sulfone system modified by bismaleimide containing tetramethylbiphenyl and aromatic ether structures

Synthesis and Curing of a Novel Combined Liquid Crystalline Epoxy

Study on the Novel Dicyanate Ester Resin Containing Naphthalene Unit

Cure Behaviour and Structure of Dicyanate-Epoxy Novolac Blends

Nonisothermal Reaction, Thermal Stability and Dynamic Mechanical Properties of Epoxy System with Novel Nonlinear Multifunctional Polyamine Hardener

Chemical, mechanical and morphological investigation on the hygrothermal aging mechanism of a toughened epoxy

Hygrothermal-resistant epoxy cured by cyanate and its composites

KINETICS OF THERMAL DECOMPOSITION OF CYANATE/EPOXY BLENDS

The hygrothermal aging process and mechanism of the novolac epoxy resin

Effects of epoxy content on dynamic mechanical behaviour of PEI-toughened dicyanate–novolac epoxy blends

Enhanced Interfacial, Mechanical, and Anti-Hygrothermal Properties of Carbon Fiber/cyanate Ester Composites with the Catalytic Sizing Agents of Titanium Epoxy

Miscibility, crystallization behavior and specific intermolecular interactions in thermosetting polymer blends of novolac epoxy resin and polyethylene glycol

Water Absorption and Property Evolution of Epoxy Resin under Hygrothermal Environment

DMTA based investigation of hygrothermal ageing of an epoxy system used in rehabilitation

Investigation on Thermal and Dimensional Stability of Epoxy Resin In-Situ Modified by Cyanate Ester Resin and Polydimethylsiloxane