Abstract:Abstract Here, numerous oxygen-containing functional groups were grafted onto the surface of CNTs to improve their dispersibility in an electrolyte. The CNTs were characterized by FT-IR, Raman, XPS, FE-SEM, and TEM. The results revealed that the dispersibility of the functionalized CNTs in the composites was better than unfunctionalized CNTs. CNTs/Ni composites were deposited on a copper plate by pulsed electrodeposition and ultrasonic dispersion using an electrolytic bath with CNTs concentrations from 0 to 2 g l −1 . The friction and wear behavior of the composite coatings were assessed using two different methods. In the first method, the coatings were scratched with a progressively higher load from 0–100 N, and the results demonstrate a 10 percent reduction in the coefficient of friction (COF) of the composite compared to pure nickel. The other method involved applying a constant load of 30 N, the COF and microscopic wear mechanism were investigated at different carbon nanotube contents, and the results confirmed that the COF of the composites was gradually reduced with the increase of carbon nanotube mass concentration, and the COF was only 0.343 when the carbon nanotube content was increased to 2 g l −1 . According to the XRD results, increasing the CNTs contents changed the preferred growth orientation. Moreover, the FE-SEM images of the wear surface of the 1 g l −1 CNTs/Ni sample indicated that it had the best wear resistance and showed the smoothest wear trace without apparent cracks. The addition of CNTs enhanced the wear resistance of the nickel matrix due to the superior mechanical strength and lubricating effect of the CNTs. CNTs exposed to the matrix surface reduced the direct contact between the Ni matrix and the friction pair, acted as lubricants, and reduced the wear rate.

Influence of CNTs on the Delay Time of Tungstenic Delay Composition

High-Frequency Analysis of Cu-Carbon Nanotube Composite Through-Silicon Vias

Preparation and Performance of Ignition Mixtures Modified by Carbon Nano-tube

Influence on (Ni-P) Electroless Composite Plating with Carbon Nanotubes

Effects of Carbon Nanotubes on the Sensitivities of Pyrotechnic Compositions

SYNTHESIS AND THE PERFORMANCE OF CARBON NANOTUBES-(Ni-P) COMPOSITES

Effects of Carbon Nanotubes Incorporation on the Grain Growth and Properties of WC/Co Nanocomposites

Influences of Carbon Nanotubes on Performance of W-Cu Composite Materials

Effect of carbon nanotube content and annealing temperature on corrosion performance of carbon nanotube/Ni composite layer

Preparation, microstructure and properties of Cu-8.3Al/CNTs composites with different volume fractions of CNTs

Influence of C2H2/N2 flow ratio on the microstructure, mechanical properties, and electrochemical behavior of TiCN composite coatings

Understanding the Influencing Mechanism of CNTs on the Microstructures and Wear Characterization of Semi-Solid Stir Casting Al-Cu-Mg-Si Alloys

Wetting behavior of AgCu-4.5Ti filler reinforced by carbon nanotubes on C/C composite

Effects of Catalyst Composition on the Synthesis of Single-Walled Carbon Nanotubes

Study on the Properties of Carbon Nanotube (CNTs) Reinforced AlSi10Mg Composites Fabricated by Powder Metallurgy

Study on the Mechanism of CNTs Regulating the Microstructures and Properties of Al–Cu–Mg Alloy

Optimization of the mechanical properties of CNTs/Cu composite by regulating the size of interfacial TiC

Investigation of the microstructure and tribological properties of CNTs/Ni composites prepared by electrodeposition

Effect of Carbon Nanotube (CNT) Content on the Properties of In-Situ Synthesis CNT Reinforced Al Composites

Effect of carbon nanotubes on microstructure and mechanical properties of TiZrVMnCu–Er high entropy alloy composites

Preparation and Self-Lubricity Investigation of CNTs/Ni Composite Coatings under Severe Conditions