Abstract:This study investigates the dispersion and compatibility of low-entangled "dis-entangled" UHMWPE (dis-UH) in a high-density polyethylene (HDPE) matrix using solvent-free melt-blending conditions and compares it with entangled UHMWPE (eUH) in the same matrix. The findings reveal that dis-UH/HDPE exhibits a significantly lower viscosity ratio than eUH/HDPE (1 and 4, respectively), indicating a lower critical capillary number ( C a critical ), thus enhanced dispersion and compatibility. Blends with varying dis-UH content up to 20 wt.% showed homogeneity, evidenced by DSC and SEM analysis, and demonstrated improved mechanical properties by 37% in the maximum stress ( σ max ) and 38% in Young's modulus ( E ). Linear viscoelasticity assessments revealed that higher dis-UH content slowed the dynamics and increased the apparent weight average molecular weight ( M w ), consistent with previous reports for linear entangled PE. The zero-shear viscosity ( scaling with M w ( η 0 M n ) was adjusted for high polydispersity, yielding a transitional point in the scaling exponent ( n ) from 3.6 to 3 at a reptation number of entanglement segments ( M r / M e ) of ∼287, in line with theoretical predictions. To rationalize the success of the homogenization process, we propose a qualitative molecular picture inspired from the constraint release Rouse mechanism involved in the disorientation process of bi-disperse linear polymers. In the case of dis-UH/HDPE blends, with initially lower density of long-long entanglements within dis-UH, and the highest density of short-short entanglements within HDPE matrix, the formation of long-short entanglements between dis-UH and HDPE is facilitated, which results in successful homogenization process. In the contrary, the establishment of long-short entanglements in eUH/HDPE blends will require unwinding of the long-long entanglements, which holds a higher kinetic barrier compared to dis-UH/HDPE blends, leading to unsuccessful homogenization.

INFLUENCE OF NETWORK ON THE INTERFACIAL DIFFUSION OF MULTILAYER POLYETHYLENE BLENDS

Enhanced Multiphase Interfacial Interaction of Impact Polypropylene Copolymer by In-Situ Introducing Polyethylene

APPLICATION OF DYNAMIC RHEOLOGICAL TECHNIQUE IN STUDYING CHAIN DIFFUSION AT POLYMER/POLYMER INTERFACE

PFG‐NMR measurement of self‐diffusion coefficients of long‐chain α‐olefins and their mixtures in semi‐crystalline polyethylene

Dynamic Rheological Behavior of Hdpe/Uhmwpe Blends

Effect of composition distribution on miscibility and co-crystallization phenomena in the blends of low density polyethylene with conventional and metallocene-based ethylene–butene copolymers

Melt blending of commercial linear polyethylene with low-entangled ultra-high molecular weight polyethylene: from dispersion compatibility to viscoelastic scaling laws

Critical Content of Ultrahigh-Molecular-Weight Polyethylene to Induce the Highest Nucleation Rate for Isotactic Polypropylene in Blends

Dynamic rheological behavior, crystallization and friction performance of ultrahigh molecular weight polyethylene/polypropylene blends by multi-step melt processing strategy

The influence of UHMWPE with varying morphologies on the non-isothermal crystallization kinetics of HDPE

Effect of small amount of ultra high molecular weight component on the crystallization behaviors of bimodal high density polyethylene

Effect of Entangled State of Nascent UHMWPE on Structural and Mechanical Properties of HDPE/UHMWPE Blends

Exploring the Entangled State and Molecular Weight Ofuhmwpeon the Microstructure and Mechanical Properties Ofhdpe/uhmwpeblends

Influence of Reduced Graphene Oxide on the Rheological Response and Chain Orientation on Shear Deformation of High Density Polyethylene

Investigation on Phase Separation Kinetics of Polyolefin Blends Through Combination of Viscoelasticity and Morphology.

Chain conformation and dynamics in ultrahigh molecular weight polyethylene melts undergoing extensional–shear coupled flow: insight from dissipative particle dynamics simulation

Morphology evolution and mechanical property enhancement of linear low‐density polyethylene by adding disentangled ultrahigh molecular weight polyethylene

Elongational Flow Field Processed Ultrahigh Molecular Weight Polyethylene/Polypropylene Blends with Distinct Interlayer Phase for Enhanced Tribological Properties

PROGRESS IN ULTRA HIGH MOLECULAR WEIGHT POLYETHYLENE/POLYPYLENE BLENDS

Enhancing Chain Mobility of Ultrahigh Molecular Weight Polyethylene by Regulating Residence Time under a Consecutive Elongational Flow for Improved Processability

Rheological Behavior and Mechanical Properties of High‐density Polyethylene Blends with Different Molecular Weights