Abstract:In response to the restrictions of the international community on the utilization of refrigerants with high GWP, the replacement of high-GWP refrigerants with non-azeotropic refrigerants and reduction in refrigerant charge have gradually become important research topics in academia. In this study, based on the VOF method, a 2D model of a sheet flow pattern was developed by considering the thermophysical properties and multicomponent phase change of a mixture. The falling-film evaporation of a non-azeotropic refrigerant composed of R32 and R134a outside a horizontal tube was numerically simulated. The effects of the spray height ( H ), tube diameter ( d ), inlet temperature ( T inlet ), Reynolds number ( Re ), heat flux ( q ), and mass fraction of R32 in the liquid-phase mixture ( M R32_liquid ) on the heat transfer coefficient ( HTC ) were studied. The results indicate that with the increase of circumferential angle ( Φ ), the local HTC exhibits a trend of decreasing, increasing, decreasing, and increasing in sequence. The largest contribution to the increase in the average HTC comes from the impact and fully developed regions. An increase in H , T inlet , and M R32_liquid is beneficial to the expansion of the fully developed region, whereas a decrease in d leads to expansion of the fully developed region. An increase in Re does not affect the extent of the fully developed region. The increase in H , Re , T inlet , and M R32_liquid increases the average HTC , but the effect of T inlet is not significant. Under the conditions of d = 24 mm, H = 13 mm, Re = 4000, M R32_liquid = 0.5, and q = 10 kW/m 2 , as the inlet temperature increases from 243.15 K to 283.15 K, the average HTC increases by 2.5%. An increase in q does not affect the average HTC , whereas an increase in d does not improve the average HTC .

Analysis on the Adiabatic Flow of R407C in Capillary Tube

Numerical Simulation and Experimental Study of Capillary Tubes

Investigating the Thermal-Hydraulic Performance of New Refrigerant Mixtures Through Numerical Simulation of Minichannel and Microchannel Evaporators

Theoretical Analyses of a New Two-Stage Absorption-Transcritical Hybrid Refrigeration System

Experimental study of ternary mixture R32/R125/R161 as alternative refrigerant to R407C

Theoretical and experimental study on a novel mixture refrigerant of R161 +R227ea

CAPABILITY ANALYSIS OF REFRIGERATION SYSTEM WITH NON-EQUILIBRIUM ADSORPTION

A Simplified Adiabatic Model For Pulse Tube Refrigerator

Optimization Analyses on the Performance of an Auto-Cascade Absorption Refrigeration System Operating with Mixed Refrigerants

Flow Boiling Heat Transfer Characteristic of Refrigerant R1234ze(E) in Horizontal Circular Tube

Experimental investigation of condensation heat transfer and pressure drop of R22, R410A and R407C in mini-tubes

Theoretical Analysis for Condensation Heat Transfer of Binary Refrigerant Mixtures with Annular Flow in Horizontal Mini-Tubes

Simulations and experiments of substitution of R41 for R23 in auto-cascade refrigeration cycle with rectifying column at -60℃

Experimental Investigation of Two-Phase Flow Boiling Heat Transfer Coefficient and Pressure Drop of R448A inside Multiport Mini-Channel Tube

Numerical simulation of heat transfer characteristics of falling-film evaporation of R32/R134a non-azeotropic refrigerant outside a horizontal tube

Studies on low GWP refrigerants flowing through capillary expansion devices used in refrigeration systems

Advanced model for a non-adiabatic capillary tube considering both subcooled liquid and non-equilibrium two-phase states of R-600a

Thermal and hydraulic analysis of a brazed aluminum evaporator

An Assessment of Friction Factor and Viscosity Correlations for Model Prediction of Refrigerant Flow in Capillary Tubes

Research on energy saving potentials using pure and zeotropic refrigerants in data center cooling systems

Condensation heat and mass transfer characteristics of low GWP zeotropic refrigerant mixture R1234yf/R32 inside a horizontal smooth tube: An experimental study and non-equilibrium film model development