Abstract:The equibiaxial planar tension test is an important method for determining the mechanical properties of hyperplastic membranes, and it is also critical to designing an effective equibiaxial tension test rig to meet experimental accuracy requirements. However, any analysis addressing the accuracy of this test is not reported in the literature. In this paper, an equibiaxial planar tension apparatus is proposed for conducting single-corner-point tension tests on hyperelastic electroactive polymer (EAP) membranes. The experimental data were compared with those obtained from two-corner-point-fixed tension tests and fitted with nonlinear material models, and the model’s parameters were also evaluated. Finally, the widely-used finite element software ABAQUS was employed to simulate equibiaxial planar tension methods and investigate the impact of clamping mode and point number on test accuracy as well as the uniformity of overall deformation. The test results indicate that the stress-strain curves for the two tensions remain consistent across small stretch ratios. However, as the stretch ratio increases (about λ > 2.25 ) in two-corner-point-fixed tension, stress shielding may lead to a degradation of strain uniformity and result in greater stresses than single-corner-point tension. Additionally, both the three-parameter Yeoh model and the four-parameter Ogden model can provide an accurate description of the EAP membrane material. The simulation results indicate that the axial strain variation amplitudes remain below 5% within a region spanning approximately 80% of the specimen’s overall length from its center to edge and even below 1% within a region spanning 85% in the single-corner-point tension; stress inaccuracies increase with stretch ratio, while the calculated error is about 2.1% when λ = 4 in the single-corner-point tension test, which has the smallest stress error among the tests; when the number of tension points is increased, the overall deformation becomes more sufficient, and the test accuracy improves as well. The conclusions drawn from this paper will be beneficial in designing equibiaxial planar tension test rigs and analyzing their accuracy and uniformity of deformation.

Pointwise Identification of Elastic Properties in Nonlinear Hyperelastic Membranes-Part I: Theoretical and Computational Developments

Pointwise Identification of Elastic Properties in Nonlinear Hyperelastic Membranes-Part Ii: Experimental Validation

A Novel Technique for Mechanical Characterization of Thin Elastomeric Membrane

Bulge Test Method for Measuring the Hyperelastic Parameters of Soft Membranes

Some Qualitative Properties of Incompressible Hyperelastic Spherical Membranes under Dynamic Loads

A Systematic Method for Characterizing the Elastic Properties and Adhesion of a Thin Polymer Membrane

Identifying heterogeneous anisotropic properties in cerebral aneurysms: a pointwise approach

A Method for Determining Elastic Constants and Boundary Conditions of Three-Dimensional Hyperelastic Materials

Characterization of the Mechanical Properties of Microscale Elastomeric Membranes

A Nonlinear Uniaxial Stress-Strain Constitutive Model for Viscoelastic Membrane Materials

An Explicit, Direct Approach to Obtain Multi-Axial Elastic Potentials Which Accurately Match Data of Four Benchmark Tests for Rubbery Materials—part 2: General Deformations

Fracture analysis of hyperelastic membrane using bond-associated non-ordinary state-based peridynamics

Machine learning based inverse modeling of full-field strain distribution for mechanical characterization of a linear elastic and heterogeneous membrane

Dynamic Characteristics in Incompressible Hyperelastic Cylindrical Membranes

A Novel Neural-Network Non-Ordinary State-Based Peridynamic Method for Large Deformation and Fracture Analysis of Hyperelastic Membrane

An innovative approach to characterize the elastic moduli of 2D materials from the central strain of bulged membrane

An Inverse Approach to Determine the Mechanical Properties of Elastoplastic Materials Using Indentation Tests

Experimental Investigations into Failures and Nonlinear Behaviors of Structural Membranes with Open Cuttings

Assessing the Mechanical Properties of Anisotropic Soft Tissues Using Guided Wave Elastography: Inverse Method and Numerical Experiments

Unified and Accurate Simulation for Large Elastic Strain Responses of Rubberlike Soft Materials under Multiple Modes of Loading

Equibiaxial Planar Tension Test Method and the Simulation Analysis for Hyperelastic EAP Membrane