Abstract:Multi-component wastewater containing a variety of organic toxins, e.g., dyes and inorganic particulates induces serious environmental concerns, which must be addressed by innovative approaches instead of conventional chemical and physical processes, which are limited by purification efficiency, secondary pollution, and cost-effectiveness. Therefore, it is important to find new avenues of purification methods that are both sustainable and effective. Ultra-fine nanofibrous microfiltration membranes were fabricated by multi-nozzle electrospinning of polyamide-66 (PA-66) and were employed to remove 0.2-μm-nanoparticles and dyes simultaneously from wastewater through filtration and dynamic adsorption performance, in an attempt to discover a one-step filtration system for both dyes and nanoparticles. The fiber diameter and surface morphology of the nanofibrous membranes varied with the concentrations of polyamide solutions, where the ultra-fine nanofibrous membrane exhibited optimum mechanical properties at a specific concentration of PA-66 (11 wt%). The nanofibrous membranes ha d adsorption capabilities of 133.3 and 204.5 mg/g, respectively, against both anionic dyes (e.g., metanil yellow) and cationic dyes (e.g., chrysoidine), respectively. The membrane also selectively filtrated fine nanoparticles with a nearly 100% rejection ratio. A multiple separation mechanism, including adsorption based on electrostatic interaction, hydrogen bonding interaction, and hydrophobic interaction, as well as depth filtration, was proposed. As an applicable demonstration, the spiral wound cartridge fabricated by PA-66 nanofibrous membrane was used for a simulated multi-component wastewater treatment that contained dyes and nanoparticles of different concentrations. During the multicomponent test at flow rate 1 mL/min, a rejection rate of 97% and greater than 99% were achieved against dyes and nanoparticles, respectively.

The Dead - End Filtration Properties of Microporous Polypropylene Hollow Fiber Membrane

Polyamide/PVC Based Composite Hollow Fiber Nanofiltration Membranes: Effect of Substrate on Properties and Performance

Fabrication of High-Flux PTFE Hollow Fiber Membranes Through Nonionic Surfactant Infiltration Coupled with Mussel-Inspired Chemistry Coating

Polypropylene Hollow-Fiber Membrane Made Using the Dissolution-Induced Pores Method

Microscopic Mechanism Of Membrane Fouling In Micro-Filtration

A dead-end filtration method to rapidly and quantitatively evaluate the fouling resistance of nylon mesh for membrane bioreactors

Dead-End Flow Filtration of Solid Suspension in Polymer Fluid Through an Active Kaolin Dynamic Membrane

Achieving highly effective non-biofouling performance for polypropylene membranes modified by UV-induced surface graft polymerization of two oppositely charged monomers.

Interface Engineering of Microporous Polypropylene Membranes for Polyamide Thin-Film Composite Nanofiltration Membranes with Robust Structure and Superior Performance

Highly permeable nanofibrous polyamide membranes for multi-component wastewater treatment: Exploration of multiple separation mechanism

Biopolymer fouling in dead-end ultrafiltration of treated domestic wastewater

Filtration Capability of the Bio-Dynamic Membrane

A Design of Composite Hollow Fiber Membranes with Tunable Performance and Reinforced Mechanical Strength

Preparation of polyethylene porous tube membrane and fouling mechanism during the filtration process

Designing Scalable Dual-Layer Composite Hollow Fiber Nanofiltration Membranes with Fully Cross-Linked Ultrathin Functional Layer

Preparation and Characterization of Microporous Polyethylene Hollow Fiber Membranes

The Filtration Properties for PEG Solutions of Different Structures Polysulfone Ultrafiltration Membranes

Filtration Behaviors and Biocake Formation Mechanism of Mesh Filters Used in Membrane Bioreactors

Fabrication of A High-Flux Thin Film Composite Hollow Fiber Nanofiltration Membrane for Wastewater Treatment

A combined model for describing the trans-membrane pressure (P) variation in constant flux dead-end microfiltration (MF) process

A continuous porous porphyrinic polymer thin-film composite membrane for anti-biofouling and molecular sieving