Abstract:PurposeThe positioning accuracy of each component is important to ensure the image quality of cone‐beam CT. However, accurate positioning is not easy and requires experience and time. The option is to calibrate the geometric parameters and then plug them into a reconstruction algorithm which is the preferred solution in practice. In this case, the image quality is determined by the accuracy and precision of the calibration method. This work describes a method to independently calibrate an imaging system in each pose (projection angle) for a cone‐beam CT with a nonideal circular trajectory.MethodsThe calibration method uses a phantom with 12 beads on 2 planes that are observed on the radiographic images. This pose‐independent calibration method (PIC) can decorrelate the relationships among the geometric parameters so that the parameters can be estimated one‐by‐one. This simplifies the calibration process. Besides the pose‐independent calibration method, this paper also describes an extended calibration method with additional constraints on the system geometry. Both methods are validated with numerical simulations and then experimentally on a practical system with a scanning object loosely supported by rotating wheels. The object rotates during the CT data acquisition. The angular and pose information of the CT system are not accurately known a priori in this case.ResultsThe numerical simulations and the experiments both provide satisfactory results. The relative error of the calibrated source‐to‐detector distance in the simulation is less than 0.1%. The errors in the calibrated roll, pitch, and yaw angles are less than 0.04°. A sensitivity study using various bead position uncertainties in random directions shows that the pose‐independent calibration method is robust to measurement errors. Tests were also done with a nonideal circular trajectory for further validation. Images reconstructed using the geometric parameters from both the pose‐independent and the extended calibration methods were free of artifacts and blur from misalignment. All these results demonstrate the effectiveness of these methods.ConclusionsThe PIC method can be used to independently calibrate the geometric parameters of a cone‐beam CT view‐by‐view. Thus, the PIC method can be implemented on commonly used systems such as circular, nonideal circular or C‐arm cone‐beam CTs. The PIC method can also be useful for some irregularly configured CT systems to fulfill special imaging requirements, for example, a CT system when the x ray source or the rotating platform cannot be easily located. The PIC method will reduce the costs of ensuring very precise mechanics and the labor in fine tuning CT systems.

Quantitative Accuracy Assessment and Optimization of SPECT Geometrical Calibration

A SVD-based Method to Assess the Uniqueness and Accuracy of SPECT Geometrical Calibration.

High Accuracy Geometrical Calibration for Half-Mm Animal Spect Imaging

[Analytical Algorithms Improving the Reconstruction of SPECT Image].

Geometrical Calibration for an Animal Pet Converted Spect

Geometric Co-Calibration of an Integrated Small Animal SPECT-CT System for Intrinsically Co-Registered Imaging

Geometric Co-Calibration of A Small Animal Spect-Ct System with Fully Superimposed Fields-Of-View

PET-based Geometrical Calibration of a Pinhole SPECT Add-on for an Animal PET Scanner

Determination of Geometrical Parameters for Slit-Slat SPECT Imaging on MicroPET

Geometrical Calibration of a PET-scanner-based Multi-Pinhole SPECT Using LYSO Background Radiation

Slit-slat Collimator Geometrical Calibration for a PET/SPECT Dual Modality Animal Scanner

System Calibration and Statistical Image Reconstruction for Ultra-High Resolution Stationary Pinhole SPECT

Optimization and Calibration of Slat Position for a SPECT With Slit-Slat Collimator and Pixelated Detector Crystals

Characterization of pinhole SPECT acquisition geometry

An Integrated Framework of Projection and Attenuation Correction for Quantitative SPECT/CT Reconstruction

Evaluation of imaging protocol for ECT based on CS image reconstruction algorithm

CT geometrical deformation calibration method in animal dual-modality CT-SPECT system

A Novel Calibration Method Incorporating Nonlinear Optimization and Ball‐bearing Markers for Cone‐beam CT with a Parameterized Trajectory

Accurate Iterative Reconstruction in Multi-pinhole SPECT Based on Simulation Point Source Measurement

Geometry Calibration Method for a Cone-Beam CT System.

Position mapping and a uniformity correction method for small-animal SPECT based on connected regional recognition