Abstract:Abstract Excessive swelling is one important factor that leads to high fuel permeability and limited operating concentration of methanol for proton exchange membranes. Herein, a collaborative strategy of main‐chain and molecular‐network engineering is applied to lower swelling ratio and improve methanol resistance for highly sulfonated polyimide. Two m ‐phenylenediamine monomers (4‐(2,3,5,6‐tetrafluoro‐4‐vinylphenoxy)benzene‐1,3‐diamine and 4,6‐bis(2,3,5,6‐tetrafluoro‐4‐vinylphenoxy)benzene‐1,3‐diamine) with tetrafluorostyrol groups are designed and synthesized. Two series of cross‐linked sulfonated polyimides (CSPI‐Ts, CSPI‐Bs) are prepared from the two diamines, 4,4′‐diaminostilbene‐2,2′‐disulfonic acid and 1,4,5,8‐naphthalenetetracarboxylicdianhydride. The rigid main‐chain structure is cornerstone for wet CSPI‐Ts and CSPI‐Bs remaining stable at elevated temperatures. The introduction of hydrophobic cross‐linked network further improves their dimensional stability and methanol resistance. CSPI‐Ts and CSPI‐Bs show obviously improved performances containing high proton conductivity (121 ± 0.27–158 ± 0.35 S cm −1 ), low swelling ratio (9.6 ± 0.40%–16.1 ± 0.01%) and methanol permeability (4.14–7.69 × 10 −7 cm 2 s −1 ) at 80 °C. The direct methanol fuel cell (DMFC) is assembled from CSPI‐T‐10 with balanced properties, and it exhibits high maximum power density (PD max ) of 82.3 and 72.6 mW cm −2 in 2 and 10 m methanol solution, respectively. The ratio of PD max in 10 m methanol solution to the value in 2 m methanol solution is as high as 88%. The CSPI‐T‐10 is promising proton exchange membrane candidate for DMFC application.

Perfluorosulfonic acid membranes treated by supercritical carbon dioxide method for direct methanol fuel cell application

PEMs with High Proton Conductivity and Excellent Methanol Resistance Based on Sulfonated Poly (aryl Ether Ketone Sulfone) Containing Comb-Shaped Structures for DMFCs Applications

MICROPOROUS PVDF-HFP-BASED POLYMER MEMBRANES FORMED FROM SUPERCRITICAL CO2 INDUCED PHASE SEPARATION *

Hybrid Proton Exchange Membranes Based on Sulfonated Poly(Phthalazinone Ether Ketone) and Zirconium Hydrogen Phosphate

Composite membranes from quaternized chitosan reinforced with surface-functionalized PVDF electrospun nanofibers for alkaline direct methanol fuel cells

Transport Properties of PFSAmembranes with Various Ion Exchange Capacities for Direct Methanolfuelcell Application

Methanol distribution and electroosmotic drag in hydrated poly(perfluorosulfonic) acid membrane.

A High-Permeance Supported Carbon Molecular Sieve Membrane Fabricated by Plasma-Enhanced Chemical Vapor Deposition Followed by Carbonization for Co2 Capture

Structural and transport properties of ultrathin perfluorosulfonic acid ionomer film in proton exchange membrane fuel cell catalyst layer: A review

Mechanical behavior of a hydrated perfluorosulfonic acid membrane at meso and nano scales

Perfluorosulfonic acid membranes with reduced hydrogen permeation by filling with carbon quantum dots for fuel cells

High-temperature low-humidity proton exchange membrane with "stream-reservoir" ionic channels for high-power-density fuel cells

Simultaneous enhancement of proton conductivity and methanol resistance of sulfonated poly(phthalazinone ether sulfone ketone)/superacid sulfated zirconia composite membranes for direct methanol fuel cells

Sulfonated Polyimide Membranes Constructed by Main‐Chain and Molecular‐Network Engineering Strategy for Direct Methanol Fuel Cell

Crosslinked Hybrid Membranes Based On Sulfonated Poly(Ether Ether Ketone)/Gamma-Methacryloxypropyltrimethoxysilane/Phosphotungstic Acid By An In Situ Sol-Gel Process For Direct Methanol Fuel Cells

Superhydrophobic Carbon Functionalized by Chemical Grafting of Fluoroalkylsilane Enables an Efficient Microporous Layer for Proton-Exchange Membrane Fuel Cells

Structural optimization and performance trade-off strategies for semi-crystalline sulfonated poly(arylene ether ketone) membranes in high-concentration direct methanol fuel cells

Reinforced Composite Membranes Based on Expanded Polytetrafluoroethylene Skeletons Modified by a Surface Sol–Gel Process for Fuel Cell Applications

In Situ Growth of COF on PAN Nanofibers to Improve Proton Conductivity and Dimensional Stability in Proton Exchange Membranes

Proton exchange membranes based on sulfonated polybutylene fumarate: Preparation and characterization

PVDF-g-PSSA and Al2O3 composite proton exchange membranes