Abstract:In this study the effect of the cutting speed and an instantaneous heating source directly before cutting tool on the cutting force, cutting zones temperatures chip morphology, shear plane angle and strain rate during dry machining of Ti6Al4V. A 2D numerical model simulating orthogonal cutting process is created using Abaqus/Explicit software. In this model, Johnson Cook constitutive model is used to describe the material behavior during cutting process. Also, Johnson Cook damage model is used to simulation chip separation mechanism. After the verification of the model by comparison with results found in the literature, a number of simulations were run at different levels of four factors: cutting speed (40, 60, 80, 100, 120 and140m/min), heat source temperature (200, 400 and 600°C), heating source distance from the cutting tool (0.3, 0.6 and 0.9mm) and heating source size/diameter (0.6, 0.8 and 1mm). Taguchi L18 orthogonal mixed level design is used to plan for simulation runs using Minitab software. ANOVA analysis is used to investigate the significance of the four factors. The response table of means and the main effect of means is used to compare between the four factors and find their ranking. Based on 95% confidence Interval (CI), the results show that cutting speed has a significant effect on cutting force, strain rate, chip compression ratio, cutting tool nose temperature, cutting tool and chip temperature in the secondary deformation zone, average chip thickness at peaks and average chip thickness at valleys and average pitch. This conclusion is based on the P-values which are << 0.05 and the contribution which reaches 99.01%. Similarly, based on P-values < 0.05 and relatively high contribution reaches 12.16%, the heating source temperature has a significant effect on average chip thickness at valleys, chip compression ratio and strain rate. The cutting speed has Rank 1 among the four factors affecting cutting force, cutting zones temperatures, chip morphology, shear plane angel and stain rate. The effect of instantaneous heating directly before cutting process is negligible compared to the effect of plastic deformation and fracture mechanism in the cutting zone.

Finite Element Simulation and Analysis of Size Effect in Micro-Milling Process

Finite Element Simulation and Analysis of Aluminum Alloy Three-Dimensional Milling

Finite Element Simulation and Analysis of Deformation in Machining of Aeronautical Aluminum Alloy Thin-Walled Workpiece

Simulation of High-Speed Milling Process of Aerospace Aluminum Alloy

Three-dimensional numerical simulation for high speed milling of aerospace aluminum alloy

Numerical Simulation Study on Milling Force for Aerospace Aluminum Alloy

Milling Error Prediction of Thin-Walled Parts During High-Speed Machining

Simulation of 3d Chip Shaping of Aluminum Alloy 7075 in Milling Processes

Study on the Effect of Tool Inclination Angle in Machining Process Based on Three-Dimensional Thermo-Elastic-Plastic Model

Numerical Simulation and Analysis of Symmetry and Step-symmetry Milling of Aerospace Thin-walled Workpiece

Finite Element Simulation of Serrated Chip Formation in High-speed Milling of A lloy Cast Iron

Analysis of milling forces in slot milling of aluminum alloy with three flutes cutter

Trochoid-path-based FEM Simulation for High-Speed Milling of Aluminum Alloy

The Finite Element Analysis Of Serrated Chip Formation In High-Speed Cuffing Auto Panel Dies

Numerical Simulation for the Milling of Alluminum Alloy Thin-Wall Workpiece with Two and Four Flutes Helical Cutter

Research on 3D Numerical Simulation and Experiment of Cutting Temperature for High Speed Milling of Aerospace Aluminum Alloy

Finite element simulation and experimental investigation on cutting mechanism in vibration-assisted micro-milling

Coupled Thermo-mechanical Model for Metal Orthogonal Cutting Process and Finite Element Simulation

Optimization of Milling Aluminum Alloy 6061-T6 using Modified Johnson-Cook Model

Finite Element Analysis of the Milling of Ti6Al4V Titanium Alloy Laser Additive Manufacturing Parts

A Novel Finite Element Model for Thermally Induced Machining of Ti6Al4V