Abstract:Al 2 O 3 thin films were deposited on the surfaces of LiFePO 4 cathodes via atomic layer deposition (ALD). Electrochemical characterization was used to evaluate the performance improvement of the cathodes coated with the ALD Al 2 O 3 thin films. In rate capability tests, an electrode coated with five ALD cycles of the Al 2 O 3 thin film exhibited the best rate performance among the tested samples when the current rate was lower than 2 C. An electrode coated with 15 ALD cycles of the Al 2 O 3 thin film delivered the highest average specific capacity—88.9 and 61.3 mAh/g at current rates of 5 C and 10 C, respectively—whereas a bare LiFePO 4 electrode did not have any capacity at the 10 C rate. These results indicate that the Al 2 O 3 coating can increase the cathode capacity at high current rates. In a cyclability test, the electrode coated with 15 ALD cycles of the Al 2 O 3 thin film retained the largest capacity after 1000 cycles at a rate of 1 C. The specific capacity of the 15ALD sample at the 1000th cycle was approximately 68% of the capacity at the first cycle, whereas this ratio was reduced to 37% for the bare LiFePO 4 electrode. These results indicate that the Al 2 O 3 coating maintains the cathode capacity after many cycles. Thicker Al 2 O 3 coatings result in a high degree of polarization and increased electrode resistance; therefore, the electrode coated with 25 ALD cycles of the Al 2 O 3 thin film exhibited a poorer rate and cycle performance than the 15ALD and 20ALD electrodes. Electrochemical impedance spectroscopy measurements and calculation of the Li + diffusion coefficient revealed that the D Li of the bare LiFePO 4 electrode was severely reduced after 1000 cycles relative to the electrode coated with 15 ALD cycles of the Al 2 O 3 thin film. This led to a faster decay in the capacity of the bare LiFePO 4 electrode after a long-duration test compared with the electrode coated with 15 ALD cycles of the Al 2 O 3 thin film. We conclude that the rate capability and cyclability of the LiFePO 4 electrode can be enhanced by depositing Al 2 O 3 ALD thin films on its surface. Under the conditions of our ALD process and electrochemical tests, 15 was found to be the optimal number of ALD cycles.

Low-temperature Atomic Layer Deposited Al2O3 Thin Film on Layer Structure Cathode for Enhanced Cycleability in Lithium-Ion Batteries

Enhanced Electrochemical Performance of LiNi0.8Co0.15Al0.05O2 Cathode Material via Li2TiO3 Nanoparticles Coating

LiAlO2-coated LiCoO2 As Cathode Material for Lithium Ion Batteries

Atomic Layer Deposition of Al2O3 on LiNi0.68Co0.10Mn0.22O2 for Enhanced Electrochemical Performance

Ultrathin ZnO Coating for Improved Electrochemical Performance of LiNi0.5Co0.2Mn0.3O2 Cathode Material

Enhanced Cycleability of LiMn2O4 Cathodes by Atomic Layer Deposition of Al2O3 Coatings

Structure and Electrochemical Performance of LiFePO4/C Cathode Materials Coated with Nano Al2O3 for Lithium-ion Battery

Structure and Electrochemical Performance of LiFePO_4/C Cathode Materials Coated with Nano Al_2O_3for Lithium-ion Battery

Enhanced electrochemical properties of Al2O3-coated LiNiPO4 cathode materials for lithium-ion batteries

Advancing Lithium-Ion Batteries' Electrochemical Performance: Ultrathin Alumina Coating on Li(Ni0.8Co0.1Mn0.1)O2 Cathode Materials

Structural characterization and electrochemical performance of AlF3-coated LiNi0.45Mn0.45Co0.10O2 as cathode materials for lithium ion batteries

Enhanced Electrochemical Stability of High-Voltage Lini0.5mn1.5o4 Cathode by Surface Modification Using Atomic Layer Deposition

Enhanced cyclability of lithium-ion batteries resulting from atomic layer deposition of Al2O3 on LiFePO4 electrodes

A hydrolysis-hydrothermal route for the synthesis of ultrathin LiAlO2-inlaid LiNi0.5Co0.2Mn0.3O2 as a high-performance cathode material for lithium ion batteries

Improving high-temperature performance of lithium-rich cathode by roll-to-roll atomic layer deposition of titania nanocoating for lithium-ion batteries

Nonuniform Growth of Sub-2 Nanometer Atomic Layer Deposited Alumina Films on Lithium Nickel Manganese Cobalt Oxide Cathode Battery Materials

Simple Solid-State Method for Synthesis of Li[Li 0.20 Mn 0.534 Ni 0.133 Co 0.133 ]O 2 Cathode Material with Improved Electrochemical Performance in Lithium-Ion Batteries

Towards high-performance cathode materials for lithium-ion batteries: Al 2 O 3 -coated LiNi 0.8 Co 0.15 Zn 0.05 O 2

Structural and Electrochemical Study of Al2O3 and TiO2 Coated Li1.2Ni0.13Mn0.54Co0.13O2 Cathode Material Using ALD

Direct Synthesis of Al2O3-modified Li(Ni0.5Co0.2Mn0.3)O2 Cathode Materials for Lithium Ion Batteries

Ultrathin Titanium Dioxide Coating Enables High-Rate and Long-Life Lithium Cobalt Oxide