Abstract:Abstract This paper presents the computational methodology and experimental investigations accomplished to enhance the efficiency of a turbine stage by applying non-axisymmetric profiling on the rotor hub wall. The experimental setup was a two-stage axial turbine, which was tested at “LISA” test facility at ETH Zurich. The first stage was considered to create the flow history for the second stage, which was the target of the optimization. The hub cavity of the second stage was designed with large dimensions as a requirement of a steam turbine. The goal was to optimize the interaction of the cavity leakage flow with the rotor passage flow to reduce the losses and increase efficiency. The computational optimization was completed using a genetic algorithm coupled with an artificial neural network on the second stage of the test turbine. Unsteady time-accurate simulations were performed using in-house developed “MULTI3” solver. Besides implementing all geometrical details (such as hub and tip cavities and fully 3D blade geometries) from the experimental setup into the computational model, it was learned that the unsteady upstream effect could not be neglected. A novel approach was introduced using unsteady inlet boundary conditions to consider the multistage effect while reducing the computational cost to half. The importance of this implementation was tested by performing a steady simulation on the optimized geometry. The predicted efficiency gain from steady simulations was 4.5 times smaller (and negligible) compared to the unsteady approach. Excluding the cavity geometry was also assessed in a different simulation setup showing 3.9% over-prediction in the absolute efficiency value. Comprehensive steady and unsteady measurements were performed utilizing pneumatic, fast response aerodynamic probe (FRAP), and fast response entropy probe (FENT) on the baseline and profiled test cases. The end wall profiling was found to be successful in weakening the strength of the hub passage vortex by a 19% reduction in the under-over turning. As a result, the blockage was reduced near the hub region leading to more uniform mass flow distribution along the span. The flow angle deviations at the higher span position were also corrected due to better control of the flow angles. Furthermore, the improvements were confirmed by reductions in entropy, secondary kinetic energy, and pressure unsteadiness. The accurate computational implementations led to an excellent agreement between the predicted and measured efficiency gain.

A Simplified CFD Method to Partial Admission Fluid Force Estimation in Turbine

Numerical Investigation of Partial Admission Losses in Radial Inflow Turbines

Rotor Dynamic Analysis On Partial Admission Control Stage In A Large Power Steam Turbine

A FLUID-THERMAL ANALYSIS OF PARTIAL ADMISSION AXIAL TURBINES

Rotordynamic Stability under Partial Admission Conditions in A Large Power Steam Turbine

Computational Fluid Dynamics Modeling Three-Dimensional Unsteady Turbulent Flow and Excitation Force in Partial Admission Air Turbine

Fluid-Thermal-Structural Analysis of Partial Admission Axial Impulse Turbines with Liquid Jet Impingement Cooling

Unsteady flow and load in 50% partial admission control stage with different admitting arc distributions

Characterization of Loss, Temperature, and Stress on Partial Admission Axial Impulse Turbines with Liquid Jet Impingement Cooling

Full 3-D Unsteady Numerical Simulation of Control Stage in Partial Admission Turbine

Numerical Simulation of Unsteady Flow Phenomena and Exciting Force in Control Stage of Steam Turbine under Multiple Working Conditions

Unsteady Interacting Flow Analysis of Ducted Propeller Based on CFD Method

Research of Flow Characteristics and Exciting Force of Unsteady Flow Under Partial Admission

Turbine Unstable Vibration and Its Reduction Method under Partial Admission Mode

A Method for Analysis of Head Cover Deformation and Vibration Amplitude in Francis Hydro-Turbine System by Combination of CFD and FEA

Analysis and Control of Part-Load Unsteady Flow in Francis Turbine’s Draft Tube

A Cfd Approach to Fluid Dynamic Optimum Design of Steam Turbine Stages with Stator and Rotor Blades

Aerodynamic Numerical Investigation Of Low-Pressure Steam Turbine Last Stage Under Low Load Conditions With Mode Decomposition Methods

C207 applications of higher-order accurate computational fluid dynamic method to steam turbine blade designs

Numerical Study on Three-Dimensional Flow in Control Stage of Steam Turbine under Multiple Working Conditions Considering Leakage Flows in Seals

Unsteady Steam Turbine Optimization Using High-Fidelity Computational Fluid Dynamics