Abstract:Highlights • Superplasticity of fine-grained Mg-10Li alloy was studied. • Severe plastic deformation was used to achieve the fine grains. • Its deformation mechanisms for superplastic flow were analyzed. • Deformation mechanism maps were constructed in 2D and 3D. The superplastic behavior and associated deformation mechanisms of a fine-grained Mg-10.1 Li-0.8Al-0.6Zn alloy (LAZ1011) with a grain size of 3.2 μm, primarily composed of the BCC β phase and a small amount of the HCP α phase, were examined in a temperature range of 473 K to 623 K. The microstructural refinement of this alloy was achieved by employing high-ratio differential speed rolling. The best superplasticity was achieved at 523 K and at strain rates of 10 −4 -5 × 10 −4 s −1 , where tensile elongations of 550–600% were obtained. During the heating and holding stage of the tensile samples prior to tensile loading, a significant increase in grain size was observed at temperatures above 573 K. Therefore, it was important to consider this effect when analyzing and understanding the superplastic deformation behavior and mechanisms. In the investigated strain rate range, the superplastic flow at low strain rates was governed by lattice diffusion-controlled grain boundary sliding, while at high strain rates, lattice diffusion-controlled dislocation climb creep was the rate-controlling deformation mechanism. It was concluded that solute drag creep is unlikely to occur. During the late stages of deformation at 523 K, it was observed that grain boundary sliding led to the agglomeration of the α phase, resulting in significant strain hardening. Deformation mechanism maps were constructed for β-Mg-Li alloys in the form of 2D and 3D formats as a function of strain rate, stress, temperature, and grain size, using the constitutive equations for various deformation mechanisms derived based on the data of the current tests.

Grain Refinement and Superplastic Behavior of 1420 Al-Li Alloy Sheets

Microstructure Evolution and Properties of Mg-9Gd-0.8Al Alloy with Lamellar Phase During Extrusion at Different Temperatures

Introducing Equiaxed Grains and Texture into Ni-Mn-Ga Alloys by Hot Extrusion for Superplasticity

Achieving high strain rate superplasticity in an Al-Cu-Li alloy processed by thermo-mechanical processing

In-situ surface study on the mechanism of high-strain-rate superplasticity in an Al–Cu–Li alloy

High Strain Rate Quasi-Superplasticity Behavior in an Ultralight Mg-9.55Li-2.92Al-0.027Y-0.026Mn Alloy Fabricated by Multidirectional Forging and Asymmetrical Rolling

Room Temperature Strengthening and High-Temperature Superplasticity of Mg-Li-Al-Sr-Y Alloy Fabricated by Asymmetric Rolling and Friction Stir Processing

Superplastic Deformation and Microstructure Evolution of Ti-55 Alloy Sheet

In-situ Study of Microstructure and Mechanical Properties of GH3536 Alloy Manufactured by Selective Laser Melting at 750 °C

Superplastic Deformation Behavior of 2 mm Ti60 Rolled Sheet in Air Environment

On Mechanical Properties and Superplasticity of Mg–15Al–1Zn Alloys Processed by Reciprocating Extrusion

Superplasticity of fine-grained Mg-10Li alloy prepared by severe plastic deformation and understanding its deformation mechanisms

Enhanced grain refinement and texture weakening in Al–Mg–Si alloy through a novel thermomechanical processing

High Strain Rate Superplasticity in Al-Zn-Mg-Based Alloy: Microstructural Design, Deformation Behavior, and Modeling

Optimization of numerical parameters and microstructure evolution on 2195 Al–Li alloy extrusion process

Microstructures, hot tensile deformation behavior and constitutive modeling in a superlight Mg-2.76Li-3Al-2.6Zn-0.39Y alloy

Crystal Plasticity Finite Element Simulation of Grain Evolution Behavior in Aluminum Alloy Rolling

Superplastic Deformation Behaviors and Power Dissipation Rate for Fine-Grained Ti-6Al-4V Titanium Alloy Processed by Direct Rolling

Effect of plastic deformation on microstructure and properties of high strength Al-Cu-Li-X aluminum-lithium alloy

Effect of Annealing Time on Grain Structure Evolution and Superplastic Response of Al-Mg 5xxx Alloys

Superplasticity of 5083 Alloys with Zr and Mn Additions Produced by Reciprocating Extrusion