Abstract:The formation of large surface grains known as peripheral coarse grains (PCG) is an undesirable feature commonly observed in extruded medium-strength Al-Mg-Si alloys produced for many applications including automotive. The objective of this study was to evaluate factors contributing to the formation of PCG layers, particularly the die bearing geometry, with the goal of developing strategies to eliminate or reduce this phenomenon. This was accomplished using a combination of extrusion trials and finite element method simulations to characterize the role of die bearing geometry on the formation of surface microstructure during the extrusion of an Al-Mg-Si-Mn alloy. The extrusion trials were conducted using two die bearing geometries, (i) a zero bearing die and (ii) a choke die using an extrusion temperature of 480 °C and ram velocities of 20 to 30 mm/s. Axisymmetric extrusion was conducted with an extrusion ratio of 16.5. During the extrusion trials, partially extruded billets were extracted from the extrusion press and water quenched in order to follow the evolution of the surface microstructure for the different bearing geometries. In addition, ram motion was arrested in the middle of the extruded length, held for 5 seconds and then resumed to investigate the role of changing the deformation conditions of the surface on the extruded microstructure. Optical microscopy and electron back-scattered scanning diffraction (EBSD) were used to quantify the microstructure and crystallographic texture of the extrudates and partially extruded billets at different spatial locations. A finite element (FE) mathematical model using the commercial software package DEFORM 2D was also developed to simulate the extrusion process so that loads, temperatures, and material flow patterns could be predicted. The FE model was used to track material flow streamlines close to the surface. Specific locations along these streamlines were then selected for EBSD analysis on the partially extruded billets. The results indicate that the major factor affecting the formation of the PCG layer is the local stored energy of the near surface material which in turn is a function of the details of the die bearing geometry.

Effect of Pocket Design on Metal Flow Through Single-Bearing Extrusion Dies to Produce A Thin-Walled Aluminium Profile

FEM-Assisted Design of a Multi-Hole Pocket Die to Extrude U-Shaped Aluminum Profiles with Different Wall Thicknesses

FEM Simulation of Aluminium Extrusion Through Two-Hole Multi-Step Pocket Dies

FE Simulation of Extrusion to Produce a Thin-Walled Wide Profile Through a Spreading Pocket Die

Study on Simulation of Stamping Forming and Die Surface Optimization of Aluminum Alloy Plate

Numerical Simulation of Cavity-Filling Procedures for Micro-Pin-fin Array Thixoforming with Semi-Solid A356 Aluminium Alloy

Extrusion of 7075 Aluminium Alloy Through Double-Pocket Dies to Manufacture a Complex Profile

On the Size Effects in Micro/meso Semisolid Extrusion–forging of A356 Aluminum Alloy

Steel-aluminum Plastic Clinching of an Inclined Wall Die

Optimization of porthole extrusion die for 6063 aluminum alloy profile with thin-walled multi-cavity complex section and analysis of profile performance

Physical Simulation Method for the Investigation of Weld Seam Formation During the Extrusion of Aluminum Alloys

Die Design and Finite Element Analysis of Welding Seams during Aluminum Alloy Tube Extrusion

Effect of Internal Pressure Distribution on Thickness Uniformity of Hydroforming Y-shaped Tube

Application of Artificial Intelligence Extrusion Die Model Based on Finite Element Simulation in Decorative Material Aluminum Alloy

Multi-Objective Optimization of a Multi-Cavity, Significant Wall Thickness Difference Extrusion Profile Mold Design for New Energy Vehicles

Research on 5A06 Aluminium Alloy Thin-wall Semisphere Hydromechanical Deep Drawing Process

The Effect of Die Bearing Geometry on Surface Recrystallization During Extrusion of an Al-Mg-Si-Mn Alloy

Optimization design of porthole die and study on microstructures and mechanical properties for an Al–Li alloy hollow profile

Numerical and Experimental Studies on the Improvement of Gas Chamber Structure During Gas-Assisted Extrusion

Optimized Design Method for Profile Extrusion Die Based on NURBS Modeling

Formation mechanism and optimization strategy of surface back-end defects in miniature complex hollow extruded profile