Abstract:In the present research, microstructure, texture, roughness, hardness, and electrochemical behavior of AISI 316L austenitic stainless steel before and after shot peening were studied to elucidate the effect of conventional and severe shot peening (CSP and SSP) processes. After the shot peening, the fraction of strain-induced martensite (SIM) and mechanical twins (MTs) in the sub-surface layer was increased. The fraction of SIM and MTs in the SSP sample was higher than in the CSP sample. The XRD patterns indicated that the SSP sample had a higher peak broadening compared to the CSP sample. In the CSP and SSP samples, a gradient microstructure was formed along the depth direction. The microstructure of the topmost layer of the CSP and SSP samples exhibited numerous ultrafine grains. The grain refining during severe shot peening was faster because of the accumulation of more strain. The CSP and SSP samples revealed a gradient distribution of elements. After the SSP, the intensity of ⟨110⟩‖ED fiber texture decreased from 12.7 to 11.6 × R and the average intensity of ⟨100⟩‖ED fiber texture increased from 1.7 to 2.0 × R, respectively, compared to the CSP sample. The surface roughness of the SSP sample (Rq = 73.6 nm and Ra = 45.2 nm) was lower than that of the CSP sample which represented the roughness decreased with surface coverage increasing from 100 % to 1500 %. Also, the wettability increased after the conventional and severe shot peening processes. In addition, the microhardness of the CSP and SSP samples showed a gradient distribution. The CSP sample had the lowest corrosion current density (0.13 μA/cm2) whereas the NP (non-peened) sample exhibited the highest current density (0.65 μA/cm2). The presence of ⟨100⟩-oriented grains in both CSP and SSP samples led to the higher corrosion resistance of shot-peened steels compared to the NP sample. The presence of favorable texture with higher intensity in the CSP sample was responsible for the higher corrosion resistance of the CSP sample compared to the SSP sample. Finally, the gradient distribution of elements along the depth direction in the CSP and SSP steels improved the corrosion resistance of the surface.

Effect of Shot Peening and Stress on Exfoliation Corrosion of 2E12-T3 Al Alloy

Influence of Shot Peening and Stress Factor on Intergranular Corrosion of 2E12 Aluminium Alloy

The Effect of Applied Tensile Stress on the Exfoliation Corrosion of 7075‐T6 Alloy

Investigation Of The Influence Of Shot Peening On Stress Corrosion Cracking Of Stainless Steel Welded Joints

INFLUENCE OF TENSILE STRESS ON EXFOLIATION CORROSION AND ELECTROCHEMICAL IMPEDANCE SPECTROSCOPY OF 7075al - ALLOY

Investigation of Wet Shot Peening on Microstructural Evolution and Tensile-Tensile Fatigue Properties of Ti-6Al-4V Alloy

Effect of shot peening on surface characteristics and high-temperature corrosion behaviour of super 13Cr martensitic stainless steel

Influence of Severe Surface Plastic Deformation Induced by Shot Peening on Microstructure and Corrosion Resistance of fine grained 316 L stainless steel

Surface characteristics and stress corrosion behavior of AA 7075-T6 aluminum alloys after different shot peening processes

Erosion-corrosion behaviour of shot peening treated nickel-aluminium bronze in simulated sand-containing seawater

Comparison of conventional and severe shot peening effects on the microstructure, texture, roughness, hardness, and electrochemical behavior of austenitic stainless steel

Effect of extrusion process on the stress corrosion cracking resistance of 7N01 aluminum alloy

Surface characteristic and corrosion resistance of different plasma-sprayed coatings (Zn, Al6061and Zn/23Al) on S960 high strength steel with subsequent micro-shot peening

Corrosion Behavior of Shot-Peened Ti6Al4V Alloy Produced via Pressure-Assisted Sintering

Effect of surface contamination on electrochemical corrosion behavior of ultrasonic shot peened TA2 alloy

Surface mechanical property and residual stress stability of nanostructured CNT/Al-Cu-Mg composites induced by shot peening

Effect of Shot Peening on Surface Damage Evolution Behavior of Cu-19Ni Alloy

Experimental Study on the Effect of Shot Peening and Re-Shot Peening on the Residual Stress Distribution and Fatigue Life of 20CrMnTi

Effect of Ultrasonic Shot Peening on Stress Corrosion of 304 Austenitic Stainless Steel

Effect of ultrasonic shot peening surface alloying on recrystallisation of a single crystal superalloy

Effect of Ultrasonic Shot Peening on the Microstructure, Surface Residual Stress, and Wear Properties of Ti-6al-4v Alloy