Abstract:Al-Zn-Mg-Cu alloy, as an important lightweight structural material in the aerospace field, has ushered in a broader application space and proposed higher performance requirements. This paper presents the experimental investigation of the effect of Zr content on the microstructure refinement and performance improvement of cast Al-5.8Zn-2.3Mg-1.7Cu alloy, aiming to optimize the additional amount of Zr, refine the alloy grains, and improve the microstructure uniformity and mechanical properties. The chemical component, phase, and microstructure were observed by inductively coupled plasma, X-ray diffraction, optical microscope and scanning electron microscope; the hardness and mechanical properties were measured by Brinell hardness tester and tensile testing machine. The addition of different contents of Zr into the alloy can form fine dispersed or primary coarse Al3Zr phase, which has a significant effect on the microstructure and mechanical properties of the alloy. The results indicate that the addition of 0.05 wt% Zr does not significantly improve the grain refinement and mechanical properties, but the Brinell hardness reaches the maximum. As the Zr content rises, the grain refinement effect becomes more obvious, while the mechanical properties first increase and then decrease. The addition amount reaches 0.20 wt%, the second dendrite arm spacing is the smallest, the ultimate tensile strength, yield strength and elongation at room temperature reach the maximum of 296.74 MPa, 249.41 MPa and 8.26%, respectively. When the amount of Zr added exceeds 0.20 wt%, the existence of coarse and brittle primary Al3Zr phase reduces the mechanical properties, and the fracture morphology changes from ductile to brittle intergranular fracture.

Effect Of Altib Nano-Grain Refiner On Mechanical Property And Damping Capacity Of Zl101 Alloy

Mechanical Properties and Damping Capacity after Grain Refinement in A356 Alloy

Study on Grain Refining and Metamorphism of ZL111 Aluminium Alloys

The Control of Nbb2 Particles in Al-Nbb2 Master Alloy and its Effect on Grain Refinement of Az91 Magnesium Alloy

Quantifying the effects of grain refiners (AlTiB and Y) on microstructure and properties in W319 alloys

Grain Refinement of Al-5Ti-0.62C-0.2Nd Grain Refiner for Commercial Pure Aluminum and Its Effect on Mechanical Properties

Study on Damping Behavior of A356 Alloy after Grain Refinement

The Grain Refinement of 1070 Alloy by Different Al-Ti-B Mater Alloys and Its Influence on the Electrical Conductivity

Enhanced grain refinement and mechanical properties of AZ91 alloy by a novel Al-5.1V-2.3B refiner containing VB 2 and VB particles

Enhanced grain refinement and mechanical properties of a high–strength Al–Zn–Mg–Cu–Zr alloy induced by TiC nano–particles

Effects of Grain Refinement on the Microstructure and Tensile Behavior of K417G Superalloy

Grain Refinement Enhanced Tensile Strength, Fracture Toughness and Fatigue Crack Propagation Resistance of a High Zn-Containing Al-Zn-Mg-Cu Alloy

Effects of new refiners on the microstructures of cast superalloy K419

Research on Refinement of the High-Strength and Ductility Al-Si Alloy

Microstructure refinement and mechanical properties enhancement of Mg Al alloys via a novel of MgO nanoparticles modified graphene nanoplates refiner by in-situ synthesis

Controllable reinforcement phase distribution at the grain scale via a simple precipitation process

Grain Refinement in A Alznmgcuti Alloy by Intensive Melt Shearing: A Multi-Step Nucleation Mechanism

Effect of Al-3 wt% Al2O3 master alloy fabricated by calcined kaolin on grain refinement and mechanical properties of A356 alloy

Influence of Zr content on microstructure and mechanical properties of As-cast Al-Zn-Mg-Cu alloy

Grain refinement of superalloys K3 and K4169 by the addition of refiners

Effect of initial mixed grain microstructure state of deformed Ni-based superalloy on its refinement behavior during two-stage annealing treatment