Abstract:Shanghai Soft X-ray FEL Test Facility (SXFEL) has started the infrastructure construction in 2015. All beam diagnostic systems are under processing and measurement, including C-band Low-Q cavity BPMs. This paper presents the progress of the cavity BPM system, including design and the measurements on a lab platform. Measurements shown that the cavity BPM frequency is 4.7GHz ± 8MHz, and the complete test platform verify that the cavity BPM system, which including signal processing electronics can work as expected. INTRODUCTION The SXFEL project at the Shanghai Synchrotron Radiation Facility (SSRF) campus serves as a test facility of China’s future hard X-ray FEL user facility, while it can be easily upgraded to a FEL user facility at“waterwindow” spectral region for scientific investigations with high brilliance X-ray pulses of ultra-fast and ultra-high resolution processes in material science and physical biosciences. The construction of the SXFEL has started since April 2015, and the first X-ray FEL light is planned to be delivered to the beam line in 2017. The SXFEL consists of following parts: 1. A photo-injector generating a bright electron beam and accelerating it to ~ 130 MeV. 2. The main linear accelerator, where the electron beam is longitudinally compressed and accelerated to ~ 840 MeV. 3. The FEL undulator complex where X-ray radiation is generated. 4. The photon beam transport & diagnostic line. To achieve the physical design of SXFEL, the diagnostic system need to achieve requirements listed in Table 1, and the dynamic is 0.1nC~0.5nC. CAVITY BPM SYSTEM The cavity BPMs have been chosen for the real time measurements of the electron beams positions along the undulator of the SXFEL. The layout is shown in Fig. 1. Figure 1: Layout of cavity BPM along undulator. Table 1: Beam Diagnostics System Specification Parameter Main technical specifications Position Stripline BPM, Resolution: 10μm@0.5nC Cavity BPM, Resolution: 1μm@0.5nC Size YAG/OTR, Resolution:30μm@1nC, Repeatablity:50μm Charge ICT, Resolution:1% Length CSR, Resolution:100fs Arrive time Phase cavity, Resolution:200 fs Cavity BPM Pickups The cavity BPM system consists of the cavity BPM probes, the RF front-end and data acquisition (DAQ) electronics is shown in Table 2. The working frequency of the position mode and the reference cavity of the CBPM are designed to be 4.7GHz preliminary to avoid the interference of the dark current caused by the frequency multiplication of the RF. The signals will be lead out through the 50Ω load and the system quality factor will be mainly determined by the external quality factor. Table 2: The Cavity BPM Design Parameter Parameter TM110 TM010 Frequency 4.7GHz 4.7GHz Q ~60 ~60 Ports number 4 2 Signal amplitude@50Ω 12mV/μm/nC (peak) 100V/nC (peak) CBPM responses with a series of simulated electron beams passing the CBPM at different positions have been modeled with MAFIA. The output signal and the corresponding spectrum at the electrode of the CBPM are shown here in Fig. 2. Stage-1 Stage-2 UN-POP UN-POP UN-POP UN-POP UN-POP UN-POP UNPRF

Simulation and Experiments for the Q(Ext) of A Cavity Beam Position Monitor

A method of bunch by bunch measurement at nanoseconds interval by using cavity beam position monitors

Cavity Beam Position Monitor Test System Based on Virtual Instrument

DESIGN AND SIMULATION OF THE WAVEGUIDE COUPLER FOR THE CAVITY BEAM MONITOR

LOW Q CAVITY BPM STUDY FOR THE BEAM POSITION MEASUREMENT OF NANOSECOND SPACED ELECTRON BUNCHES *

Optimization of the Cavity Beam-Position Monitor System for the Shanghai Soft X-ray Free-Electron Laser User Facility

Design and Measurement of Signal Processing System for Cavity Beam Position Monitor

Study of the Crosstalk Evaluation for Cavity BPM

Research of Coupling Coefficient Extraction of a Cavity Resonator

Progress of Cavity Beam Position Monitor at SXFEL

In situ beam trajectory tilt measurement based on single cavity beam position monitor

DEVELOPMENT OF THE SIMULATION SOFTWARE PACKAGE FOR THE CBPM SYSTEM *

Design and cold test of a rectangular cavity beam position monitor

Beam test results of high Q CBPM prototype for SXFEL

High-Order Mode-Matching-Based Single-Cavity Coaxial Transducer for Broadband Measurement of Complex Permittivity

C-Band Deflecting Cavity for Bunch Length Measurement of 2.5 MeV Electron Beam

Simulation and Experimental Studies on a 4 Rod RFQ RF Property

COMPARISON OF MEASURED AND CALCULATED COUPLING BETWEEN A WAVEGUIDE AND AN RF CAVITY USING CST Microwave Studio

Development and cold-test of an RFQ-DTL coupled cavity

Design and Simulation of a high order mode cavity bunch length monitor

Design and Cold Measurements of a Coupled RFQ-SFRFQ Cavity