Abstract:Selective laser sintering (SLS) combined with reaction melt infiltration was used to fabricate Si–SiC ceramic matrix composites, and the effects of different concentrations of phenolic resin (PF) on the properties of the SLS green body and carbonized and final Si–SiC samples were investigated. The results showed that the impregnation with PF can increase the bulk density, reduce the porosity of the samples at all stages, and improve the mechanical properties of the reactive bonded samples. The degree of densification and mechanical properties of the sample gradually enhanced with an increase in PF concentration. The main phases of the Si–SiC composites were free Si, α-SiC, β-SiC, plus an extremely small amount of Al–Si alloy, and the SiC and the Si phase contents increased and decreased, respectively, as the concentration of PF increased when measured using Rietveld refinement and image analysis software. The macroscopic properties of the samples improved greatly after precursor infiltration pyrolysis (PIP) treatment with 66.7%vol PF-ethanol solution twice. According to the crystal nucleation-growth theory, it was inferred that the infiltrated PF could provide a certain amount of pyrolytic carbon in the carbonized specimen. During the reaction bonded process, the carbon formed by carbonization pyrolysis first dissolves into the molten Si and reaches saturation. With the further dissolution of carbon, [C] and [Si] in the liquid phase contact each other to form β-SiC nuclei, the nuclei that precipitate at the pore wall position and gradually form a continuous interfacial layer of β-SiC. The β-SiC layer prevents the liquid Si from direct contact with C inside the prefabricated body, therefore, further reactants diffuse through the layer. Finally, the fine crystalline β-SiC grains were fabricated inside the specimen.

Effect of Phenolic Resin on the Basic Properties of Woodceramics and Biomorphic SiC Ceramics

Novel Silicon-Modified Phenolic Novolac Resins: Non-isothermal Curing Kinetics, and Mechanical and Thermal Properties of Their Biofiber-Reinforced Composites

Porous SiC Ceramic Prepared by Reactive Infiltration of Liquid Silicon into Woodceramics

Woodceramics Prepared from Basswood Powder and Phenolic Resin

Structure and basic properties of woodceramics made from phenolic resin–basswood powder composite

Preparation of Macroporous SiC from Si and Wood Powder Using Infiltration-Reaction Process

STUDY ON STRUCTURAL CHANGES DURING PREPARING WOODCERAMICS FROM PHENOLIC RESIN/BASSWOOD POWDER COMPOSITE

Effect of impregnated phenolic resin on the properties of Si–SiC ceramic matrix composites fabricated by SLS-RMI

Effect of Holding Time on the Basic Properties of Biomorphic Sic Ceramic Derived from Beech Wood

Effect of starting Si contents on the properties and structure of biomorphic SiC ceramics

Improved Thermal Stabilities, Ablation and Mechanical Properties for Carbon Fibers/Phenolic Resins Laminated Composites Modified by Silicon-containing Polyborazine

Preparation of Biomorphic SiC/C Ceramics from Pine Wood Via Supercritical Ethanol Infiltration

Microstructure analysis of morph-genetic SiC/C ceramics from wood

Preparation and Properties of Porous Microcellular SiC Ceramics by Reactive Infiltration of Si Vapor into Carbonized Basswood

Effects of phenolic resin contents on microstructures and properties of c/sic‐diamond composites

PREPARATION OF MACROPOROUS SiC FROM WOODCERAMICS AND SILICON POWDER BY IN SITU REACTION-SINTERING PROCESS

Woodceramics Prepared from Wood Powder/Phenolated Wood Composite

Study on preparation and properties of wood-ceramics

Mechanical Properties and Microstructure of Si/Sic Materials Derived from Native Wood

Study of Phase Transition, Structure Modulation, and Thermal Properties of Si/B-modified Bisphenol a Phenolic Resin Ceramicizable Materials

Effect of carbonization temperature on the basic properties of woodceramics made from carbonized bamboo fiber and liquefied wood