Abstract:In the present work, (TiBw+TiCp)/Ti6242 composites with TiB:TiC=1:1 were produced by common casting and hot-forging technology utilizing the SHS reactions between titanium and B4C, C powder. The microstructures of composites were examined using optical microscopy (OM) and transmission electron microscopy (TEM). The X-ray diffraction (XRD) was used to identify the phases that were present in the composites. There are three phases — TiB, TiC and titanium matrix alloy. TiB grows in short-fiber shape, whereas TiC grows in dendritic, equiaxed or near-equiaxed shape. TiB whiskers were made to align the longitudinal direction and TiC dendritic was broken up after hot-forging. The reinforcements are distributed uniformly in matrix alloy. The interfaces between reinforcements and titanium matrix alloy are very clean. The tensile strength (yield strength and ultimate tensile strength) and the Young's modulus improve with the addition of TiB whiskers and TiC particles although some reduction in ductility is observed. (TiBw+TiCp)/Ti6242 composites with TiB:TiC=4:1 will fracture on a lower level of applied stain due to deformation restraint of TiB whiskers on titanium matrix alloy. The (TiBw+TiCp)/Ti6242 composites with TiB:TiC=1:1 show higher tensile strength and ductility. The addition of graphite not only improves the tensile strength and the Young's modulus but also increases the ductility. The improved Young's moduli and increased tensile strengths of the composites are explained using shear lag and rule-of mixtures theories. The Young's moduli of the composites were found in good agreement with that calculated from Tsai–Halpin equation applied for discontinuous-reinforced composites.

Microstructure and Properties of TiC Reinforced 304 Stainless Steel

Microstructure, Mechanical Properties and Wear Resistance of Low Alloy Abrasion Resistant Martensitic Steel Reinforced with TiC Particles

Strengthening Effects of Tic Particles and Microstructure Refinement in in Situ Tic-Reinforced Ti Matrix Composites

Microstructure and Compressive Properties Ofin SituSynthesized TiC/Ti Composites

Microstructure, mechanical properties and strengthening mechanism of in-situ synthesized TiC/6061 nanocomposites

Investigation on Microstructures and Mechanical Behavior of In-Situ Synthesized TiC and TiB Reinforced Ti6Al4V Based Composite

Microstructure and tensile properties of in situ synthesized (TiBw + TiCp)/Ti6242 composites

Microstructure and Tensile Properties of in Situ Synthesized (Tib+tic)/ti-6Al-4v Composites

Microstructure and Mechanical Properties of in Situ Synthesized TiC/Ti Composites

Effect of Carbon Element on Mechanical Properties of in Situ 5 Vol% TiC/Ti-1100 Composite

Effects of TiC formation on the microstructure and hardness of wear-resistant steel

Design, fabrication, microstructure and properties of in-situ synthesized TiC reinforced stainless steel matrix composite coating by laser cladding

Microstructure and Tensile Properties of in Situ (tib+tic)/ti6242 (tib:Tic=1:1) Composites Prepared by Common Casting Technique

Effect of TiC Content on Microstructure and Mechanical Properties of High-temperature Titanium Matrix Composites

Simultaneously enhanced strength and toughness of cast medium carbon steels matrix composites by trace nano-sized TiC particles

Improved Wear and Corrosion Resistance in TiC-Reinforced SUS304 Stainless Steel

Microstructure and compressive properties of in situ synthesized (TiB + TiC)/Ti composites

Microstructure, mechanical properties and strengthening mechanisms of in-situ prepared (Ti5Si3 + TiC0.67)/TC4 composites

Dry Sliding Wear Properties of Annealed Carbon Steels Matrix Composites by Nanosized TiC‐TiB2 Particles

Microstructure and mechanical properties of 12wt.% Cr ferritic stainless steel with Ti and Nb dual stabilization

Strengthening Effect of in Situ Tic Particles in Ti Matrix Composite at Temperature Range for Hot Working