Abstract:Proceedings of the Institution of Mechanical Engineers, Part L: Journal of Materials: Design and Applications, Ahead of Print. The Cu–6Al–2Ni alloy has much higher ultimate tensile strength compared to pure copper and may potentially replace it in the dissimilar joints between titanium alloys and stainless steels. Laser welding of aluminum bronze to stainless steel has not been reported in the scientific literature, which motivated the present weldability study of Cu–6Al–2Ni/316L dissimilar joint with a continuous ytterbium Yb:YAG laser. Different laser spot offsets from the joint line were selected in order to produce the joints with various dilutions of welded materials. Scanning electron microscopy with energy-dispersive X-ray spectroscopy (SEM-EDS) probe and X-ray diffraction (XRD) analyses of the melted zones were performed, along with microhardness measurements and tensile testing. The phase evolution in the obtained microstructures was evaluated using Thermo-Calc software. For the dilutions ranging from 23 to 63 at.% Cu, the melted zones showed globular microstructures with primary and secondary phase separation due to the miscibility gap existing in the Cu–Fe system. Lower Cu contents resulted in cellular γ-Fe structures with rare globular Cu-rich inclusions. The XRD analysis indicated the presence of ∼10% of ternary AlFe2Ni phase, however, it did not harm the mechanical properties of the welds. According to Thermo-Calc, this phase is formed from γ-Fe during the cooling process. Microhardness measurements did not indicate the embrittlement of the melted zones, which can be explained by the submicronic dispersion of AlFe2Ni. The welds exhibited a ductile fracture in Cu–6Al–2Ni at ultimate tensile strength of 350–420 MPa in a wide range of laser offsets, which is much higher than previously reported results for pure copper/316L joints.

Laser Welding of Dissimilar Metals Aided by Unsteady Thermal Conduction Boundary Element Method Analysis

203 Laser Welding of Steel and Aluminum Alloy Dissimilar Materials

Deep-penetration welding-brazing of aluminum/steel dissimilar metal using laser-MIG arc hybrid heat source

Laser Conduction Welding Characteristics of Dissimilar Metals Mg/Ti with Al Interlayer

Analysis of laser welding on dissimilar materials with the influence of adding interlayer

Experimental and numerical assessment of interfacial microstructure evolution in dissimilar Al/steel joint by diode laser welding-brazing

Hybrid Resistance-Laser Spot Welding of Aluminum to Steel Dissimilar Materials: Microstructure and Mechanical Properties

Research on Interface Characteristic of Laser Welding Joints of Steel/Aluminum Dissimilar Materials

Laser techniques for dissimilar joining of aluminum alloys to steels: A critical review

Study on Laser Overlap Welding of Titanium/Aluminum Dissimilar Metals Based on Niobium Microalloying

Dissimilar Laser Welding of Superelastic NiTi and CuAlMn Shape Memory Alloys

High-speed hot-wire laser brazing technology for steel/aluminum alloy dissimilar joint using twin beam irradiation

A Review: Laser Welding of Dissimilar Materials (Al/Fe, Al/Ti, Al/Cu)—Methods and Techniques, Microstructure and Properties

Dissimilar welding between Cu–6Al–2Ni alloy and stainless steel 316L using continuous ytterbium YAG laser

Effect of heat input on interfacial microstructure, tensile and bending properties of dissimilar Al/steel lap joints by laser Welding-brazing

Effect of laser beam models on laser welding–brazing Al to steel

Interfacial microstructure and strengthening mechanism of dissimilar laser al/steel joint via a porous high entropy alloy coating

Dissimilar Laser Welding/Brazing of 5754 Aluminum Alloy to DP 980 Steel: Mechanical Properties and Interfacial Microstructure

Fiber Laser Welding Of Similar And Dissimilar Aluminum Alloys

Research on the Laser Welding Process and Performance Analysis of SiCp/Al Composite and 2A14 Aluminum Alloy Dissimilar Metals

Effect of Heat Input on a Laser Powder Deposited Al/steel Butt Joint