Abstract:Dissimilar lap joining of AZ31B Mg alloy to Cu-Ni coated Ti-6Al-4V was carried out by laser welding-brazing method. The effect of Cu and Ni contents on interfacial reaction and joint fracture load were analyzed. For the joint in which the Ni coating (15.36 mu m) was thicker than the Cu coating (5.47 mu m), thick intermetallic compound (IMC) composed of a mixture of light gray Al-Ni-Ti + Ti3Al + Ti2Ni phases mingled with dark gray Ti3Al was produced at the interface. In comparison, a mixed interfacial reaction layer consisted of Ti2Ni and Ti3Al was formed from the direct irradiation zone to the weld toe zone of the joint with comparable Ni and Cu coating thicknesses (10.78 mu m Cu-9.30 mu m Ni). In this case, the thickness of the mixed layer was below the critical thickness of 10 mu m. For the joint in which the Cu coating is much higher than the Ni coating thickness (17.12 mu m Cu-4.23 mu m Ni), Ti3Al and Ti2Ni mixed reaction layer was produced at the brazed interface of direct irradiation zone, whereas, only Ti3Al phase was formed at the middle zone. At the weld toe zone, Ti2Cu uneven interfacial reaction layer was evolved. With increasing Cu and decreasing Ni coating thicknesses, the fracture load first increased and then slightly decreased, the maximum tensile-shear fracture load attained 2020 N for joints with comparable Cu and Ni coating thicknesses. This is twofold higher than that of uncoated joint. The tensile-shear investigation showed that the joint would fracture at the fusion zone when the coating thickness of Ni was comparable or higher than Cu. In contrast, interfacial failure was observed when the thickness of Cu was much higher than the Ni. For the joint with interfacial failure mode, tear ridge was observed from the fracture surface, whereas, the fusion zone fracture surfaces was noted to display a typical dimple feature.

Laser Conduction Welding Characteristics of Dissimilar Metals Mg/Ti with Al Interlayer

Microstructure and Thermodynamic Behavior of Laser Welded-Brazed Mg/Ti Dissimilar Joint

Laser Welding of AZ31Mg Alloy with 6061al Alloy Via Ti Interlayer Based on Two Kinds of Bonding Mechanisms

Dissimilar Joining of AZ31B Mg Alloy to Ni-coated Ti-6Al-4V by Laser Heat-Conduction Welding Process

Numerical study of heat and mass transfer in dissimilar laser welding of Mg/Al lap-joint with Ti interlayer

Influence of Al Interlayer Thickness on Laser Welding of Mg/Steel

Influence of Al Interlayer Thickness on Laser Welding of Mg / Steel The impact of different Al interlayer thicknesses on interfacial reactions and mechanical properties during laser welding of Mg to steel was investigated

Microstructure and Properties of 6063/ti3al2.5v Dissimilar Alloys Joint with Laser Welding

Laser Welding-Brazing of Immiscible AZ31B Mg and Ti-6Al-4V Alloys Using an Electrodeposited Cu Interlayer

Microstructure and Tensile Behavior of Laser Arc Hybrid Welded Dissimilar Al and Ti Alloys

Effect of Al Content in Magnesium Alloy on Microstructure and Mechanical Properties of Laser-Welded Mg/Ti Dissimilar Joints

Dissimilar Ti/Mg Alloy Butt Welding by Fibre Laser with Mg Filler Wire – Preliminary Study

Enhanced Interfacial Reaction and Mechanical Properties of Laser Welded-Brazed Mg/Ti Joints with Al Element from Filler

Microstructure and properties of laser welding-brazingjoint of Ti/Al dissimilar alloys

Microstructures and Mechanical Properties of Ti<sub>3</sub>Al-Nb/SUS301L Laser-Welded Joint with V and Cu Interlayer

Laser Spot WeldingCharacteristics of Dissimilar Metals: TC4Titanium/5052Aluminum

Microstructure of Laser-Tig Hybrid Welding Joint of Dissimilar Metals of Al and Mg

Influence of Electrodeposited Cu-Ni Layer on Interfacial Reaction and Mechanical Properties of Laser Welded-Brazed Mg/Ti Lap Joints

Influence of Ni coating on interfacial reactions and mechanical properties in laser welding-brazing of Mg/Ti butt joint

Effects of AlSi12 Interlayer on Microstructure and Mechanical Properties of Laser Welded 5a06/ti6al4v Joints

Effect of Copper-Nickel Interlayer Thickness on Laser Welding-Brazing of Mg/Ti Alloy