Abstract:Large aluminum alloy ring forgings are the core components of heavy-duty rocket fuel storage tanks, and the large residual stress inside the rings leads to poor shape accuracy of large thin-walled parts. The initial stress of the 2219 aluminum alloy ring blank was tested using the drilling method, and the creep constitutive coefficient of the 2219 aluminum alloy was determined through stress relaxation tests. The numerical simulation processes of thermal stress relief (TSR), vibration stress relief (VSR), and thermal–vibration stress relief (TVSR) were compared and established. Through the correlation analysis between the actual measurement results of residual stress and the simulation results, it can be seen that the strong correlation in three directions at each measurement point accounts for over 37.5%, and the moderate correlation accounts for over 62.5%. This indicates that the numerical simulation model of 2219 aluminum alloy ring containing initial residual stress can accurately reflect the size and distribution of residual stress inside the actual ring. The simulation results show that the derived constitutive model can describe the stress relaxation process of TVSR by combining a single thermal time effect stress relaxation constitutive theory with a VSR plastic deformation material model. The simulation models established above were used to calculate the residual stress homogenization ability of three types of aging. The results showed that VSR, TSR, and TVSR can homogenize and reduce the residual stress field inside the ring, improve the distribution of residual stress inside the ring, and have a better overall homogenization ability of TVSR. The VSR control has a certain effect on reducing and homogenizing residual stress, but compared with TSR and TVSR, the reduction and homogenization ability of residual stress control is limited. The homogenization control effect TVSR > TSR > VSR, and the maximum equivalent stress homogenization rates of VSR, TSR, and TVSR are 52.8%, 80.6%, and 82.2%, respectively. Then, numerical simulation technology was used to study how the initial residual stress in the blank causes the deformation of the ring during the thin-walled machining process. The roundness error theory of the minimum containment area method was applied to evaluate the deformation degree during the thin-walled numerical machining process, and the TVSR method was used for stress regulation. The deformation law of the thin-walled machining of the ring under different aging parameters was studied.

Coordinative Deformation Research on Local Loading Continuous Forming for Large Aluminum Alloy Ring

Reverse Deformation Design for Bending Control in Welding of Ring Stiffeners

Analytical calculation model for radial-axial coordinated feed strategy in large-scale flat ring rolling based on ultimate bending moment

Numerical Simulation Research on Mandrel reaming of Ring Steel Ingot

Research on plastic deformation law and forming technology of rotary forging with multi-cone rolls

Numerical Simulation and Experiment of Stress Relief and Processing Deformation of 2219 Aluminum Alloy Ring

Investigation of the Diffluence Mechanism of an Aluminium Alloy Ring under Compression

Diffluence Behaviour of Aluminium Alloy During Ring Compression

Research on plastic deformation transfer and distribution of large-diameter thin-walled metal ring parts in double-roll pendulum hot rotary forging process

Numerical Simulation for Forging Process of Bearing Rings

Forming process chain for manufacturing complex conical-section profiled rings: On a co-design method

Research on machining deformation of aluminum alloy rolled ring induced by residual stress

Buckling Defect Optimization of Constrained Ring Rolling of Thin-Walled Conical Rings with Inner High Ribs Combining Response Surface Method with FEM

A non-sequential isothermal local-loading forming process for large-scale rib-web components

3D FE modeling simulation of the double-roll hot rotary forging of large diameter thin-walled metal disk

Deformation Behaviors of Laser Forming of Ring Sheet Metals

Frictional Behavior During Cold Ring Compression Process of Aluminum Alloy 5052

Deformation Analysis of Double-Sided Tube Hydroforming in Square-Section Die

Study on Roll Forming Process Simulation and Roll Diameters Optimization

A novel process for manufacturing large-diameter thin-walled metal ring: Double-roll pendulum hot rotary forging technology

A New Fe Modeling Method for Isothermal Local Loading Process of Large-Scale Complex Titanium Alloy Components Based on Deform-3d