Abstract:In order to solve the shortcomings of the current traditional commercial polyolefin microporous membranes with worse thermostability at high temperature, polyimide (PI) nanofiber membranes prepared by electrospinning are promising separators for lithium ion batteries that operate at high temperatures. This preparation includes the forming process of poly(amic acid) (PAA) fibers membrane and thermal-imidization process. In this study, we design the experiment of thermal-imidization for PAA fibers to improve the mechanical strength and the electrochemical performance of the obtained PI nanofiber membrane. It is found that the degradation phenomenon and the crosslinking function occur after the imidization during the heat treatment. The mechanical strength of PI nanofiber membrane gets improved with new crosslinking system after being heat-treated at 350 °C. LiCoO2/Li cells based on such PI nanofiber membranes exhibit excellent cycle performance (300 cycles) and rate performance (even at high rates of 6 C), better than those employing polyolefin microporous membranes.Graphic abstractDuring the heat treatment of polyamic acid, a thermal imidization process will occur. At the same time, different heat treatment temperatures will lead to differences in the degree of imidization and the structure of the fiber membrane material. It is important to understand the thermal imidization process. The effect of thermal imidization temperature on the performance of the electrospun polyimide lithium ion battery separator is studied. The experimental results show that although the degree of imidization is decreased by the heat treatment at 350 °C, it has better cycle performance (300 circles) and rate performance (even at high rates of 6 C).

Study on Insulation Non-woven Membrane of Polyimide by Electrospinning

Characterization of ODPA-ODA polyimide non-woven membranes prepared by electrospinning

Study on the Rheological Properties of Fluorinated Polyimide Spinning Solution

Thermal and Dielectric Properties of Electrospun Fiber Membranes from Polyimides with Different Structural Units

Preparation of the Ultra-Low Dielectric Constant Polyimide Fiber Membranes Enabled by Electrospinning

The Study On Fabrication Of Insulated Membrane By Electrospinning

The Trap and Dielectric Characteristics of Polyimide Nanofiber Membranes at Different Temperatures

Preparation and Characterization of the PMIA Fibrous Membrane

Electrospinning Fabrication of High Strength and Toughness Polyimide Nanofiber Membranes Containing Multiwalled Carbon Nanotubes

Optical and Electrical Properties of Polyimide Thin Films Grown by Vapor Deposition Polymerization

Novel Polyimide Materials Produced By Electrospinning

High-performance polyimide nanofiber membranes prepared by electrospinning

Controlled preparation of polyimide/polysulfone amide (PI/PSA) porous micro-nano fiber membranes by microemulsion electrospinning for excellent thermal insulation

Effect of the molar mass of polyimide based on pyromellitic dianhydride and 4,4′‐oxydianiline on dielectric and mechanical properties of nonwoven oriented polyimide materials

Preparation and Separation Properties of Electrospinning Modified Membrane with Ionic Liquid Terminating Polyimide/Polyvinylpyrrolidone@Polydopamine

The effects of electrospinning parameters on coaxial polyacrylonitrile/polyurethane nanofibers: Morphology and water vapour transmission rate

Structural evolution from poly(amic acid) to polyimide fibers during thermal imidization process

An Ultraviolet-Assisted Electrospinning Procedure of Polyimide Ultrafine Fibrous Membranes Fabricated by Ester-Type Negative Photosensitive Polyimide

Preparation of Polyimide Nanofiber Membrane with Gradient Wettability by Electrospinning

Influences of Different Imidization Conditions on Polyimide Fiber Properties and Structure

Effect of the heat treatment temperature on mechanical and electrochemical properties of polyimide separator for lithium ion batteries