Abstract:Wear resistant composite layers were fabricated on 38CrMoAl steel by laser processing with NiCr/Cr3C2-CeO2 powders with addition of MoS2 or WS2. The composite layers were heat treated at 150 and 300 degrees C (MoS2), and 3(X) and 600 degrees C (WS2). Microstructure, phases, microhardness, wear behaviour at room temperature and crack behaviour under loading of the laser processed and heat treated layers were investigated. Results indicate that undissolved MoS2 or WS2 were observed in all the layers. Heat treatment changed the microstructure and phases of all the laser processed layers. When the original majority phase of the laser processed layer was martensite, volume fraction of retained austenite increased after heat treatment; while when the original majority phase was austenite, volume fraction of retained austenite decreased after heat treatment. Full width at half maximum (FWHM) of martensite peaks in the laser processed layer with addition of 20 wt.% MoS2 decreased with heat treatment temperatures. indicating reduced defects in the heat treated layers. Laser processed layers with addition of 10 wt.% MoS2 10 wt.% or 20 wt.% WS2 without heat treatment showed the best wear resistance while that with addition of 20 wt.% MoS2 showed the best wear resistance after heat treatment at 300 degrees C. The wear mechanism of all the layers is abrasive, adhesive and oxidative wear, accompanied by the formation and removal of oxide film and sulphide containing tribofilms. The oxide film and sulphide lubricating phases formed on the worn surface during sliding wear play an important role in reducing friction and wear loss. Un-dissolved MoS2/WS2 and crack behaviour in case of loading is closely related to the microstructure of the pressed matrix.

The Wear-Resistance of 3Cr2W8V Steel with Cave Pit Non-Smooth Surface Processed by Laser

Wear Resistance of 3cr2w8v Rough Surfaces

Properties of 3cr2w8v Die Steel with Striations Processed by Laser

Wear-Resistance of Die Steel with Non-Smooth Surface Used to Pressure Casting Die Processed by Laser

Wear Behavior of Die Steel with Non-smooth Surface in Different Shape and Distance

Wear Resistance of Die Casting Die of Cover Lid of Engine by Laser Treatment

Thermal fatigue behavior of 3Cr2W8V die steel with biomimetic non-smooth surface

Surface Morphology of Laser Tracks Used for Forming the Non-Smooth Biomimetic Unit of 3cr2w8v Steel under Different Processing Parameters

Microstructure and wear behavior of arc-shaped 40CrNiMo steel after laser hardening

The Resistance to Wear and Thermal Cracking of Laser Surface Engineered P20 Steel

Optimization of Laser Processing Parameters and Their Effect on Penetration Depth and Surface Roughness of Biomimetic Units on the Surface of 3cr2w8v Steel

Microstructure and Wear Behaviour of 38CrMoAl Steel Laser-Processed with the Addition of MoS2 or WS2

Effects of Process Parameters on Microstructure and Wear Properties of 40CrNiMo Steel by Laser Transformation Hardening

Impact wear behavior of laser hardened hypoeutectoid 2Cr13 martensite stainless steel

Research on High Temperature Wear of 3Cr2W8V Steel

Experimental Study on the Wear Properties of 42CrMo Steel with Different Microstructures and T15 Laser Cladding

Microstructure and wear resistance enhancement of semi-steel rolls by laser surface alloying of NiCr-Cr3C2

Influence of Laser Energy Density on Acquisition and Wear Resistance of Bionic Semisolid Unit of 40cr Steel

Wear resistance of a bearing steel processed by laser surface remelting cooled by water

Microstructure and Wear Resistance of Laser Cladding NiCrMn-WC Composite Coatings

Wear and corrosion behavior of laser clad Cr3Si reinforced intermetallic composite coatings