Abstract:Electroactive polypyrrole (Pg) thin films were grown by potentiostatic electropolymerization at chemically derivatized interdigitated microsensor electrodes (IMEs) of gold on borosilicate glass leading to specific adhesion of the electroconductive polymer film to the device. Films were grown to a constant electropolymerization charge density of 70 mC/cm(2) at 0.65 V vs Ag-0/AgCl, 3 M Cl- from 1.0 M aqueous pyrrole solutions containing 2.5 mM poly(styrenesulfonic acid) (PSSA) and 2.5 mM dodecylbenzynesulfonate with the pH adjusted to 3.0 and the temperature maintained at 20 degrees C. The interdigit space of the IME devices was chemically derivatized by chemical modification with (3-aminopropyl)trimethoxysilane followed by direct linking of the primary amine to the carboxylic acid of 3-(1-pyrrolyl)propionic acid using the heterobifunctional linker 1,3-diisopropylcarbodiimide enhanced with N-hydroxysulfosuccinimide in aqueous solution. XPS evidence supports the immobilization of omega-(1-pyrrolyl) moieties to the device surface. The 3-(1-pyrrolyl)propionic acid was shown to be electroactive, electropolymerizable, and co-electropolymerizable with pyrrole monomer from aqueous solution. Electroconductive PPy films grown on these omega-(1-pyrrolyl) derivatized IME devices were allowed to bridge the interdigit space and so pyrrole monomer was co-electropolymerized with omega-(1-pyrrolyl) moieties specifically attached to the interdigit space of the device. This leads to specific adhesion of the PPy thin film to the device surface. Films grown in this way were compared to films similarly grown on unmodified devices, on IME: devices rendered hydrophobic by chemical modification with dodecyltrichlorosilane, and on devices modified with (3-aminopropyl)trimethoxysilane. Cyclic voltammetry revealed no significant difference in the electroactivity of PPy films grown on these various IME surfaces. Films were also characterized by the time to adhesive failure using the adhesive tape test following immersion in PBKCl 7.2 buffer or after being maintained dry under vacuum and over desiccating molecular sieves. The time to adhesive failure in both test environments occurred in the order unmodified < dodecyltrichlorosilane modified much less than (3-aminopropyl)trimethoxysilane modified much less than omega-(1-pyrrolyl) derivatized. The failure times were 3 days < 5 days much less than 27 days much less than 235 + days for films immersed in aqueous buffer and were 3 days < 36+ days much less than 235+ days much less than 235+ days for films stored dry under vacuum. The electrochemical and adhesion test evidence suggest that the PPy films are specifically immobilized to the omega-(1-pyrrolyl) derivatized IME: devices and that this negates the hydrolytic instability of the PPy/glass interface that leads to poor adhesion under physiologic conditions.

Patterned Self-Assembled Film Guided Electrodeposition

Manipulation of the ultimate pattern of polypyrrole film on self-assembled monolayer patterned substrate by negative or positive electrodeposition

Electrochemical Deposition of Polypyrrole on Patterned Self-Assembled Monolayers

Electrochemical Study of a Polypyrrole Film/Decanethiol Self-Assembled Monolayer on a Gold Electrode

Patterns of Conducting Polypyrrole with Tunable Morphologies

Electrochemical Thin Film Deposition of Polypyrrole on Different Substrates

Fabrication of polypyrrole micropatterns through microchannel-confined electropolymerization and their electrical conductivities

Modifying substrate surfaces with self-assembled polyelectrolyte layers to promote the formation of uniform polypyrrole films

Selective Electrodeposition and Etching on Polymer Brush Template Prepared by Patterned Monolayer Surface Initiated Polymerization

Electrochemical Behavior and Surface Morphology of Conducting Polypyrrole

Highly Electrically Conductive PEDOT:PSS Films via Layer-By-Layer Electrostatic Self-Assembly

Preparation of PEDOT Film by Liquid Phase Depositional Polymerization

Patterning of polypyrrole using protein-based template and their potential application in resist

Application of Al2O3 in the electrosynthesis of polypyrrole with fuzzy morphology—Microtentacle

Specific immobilization of electropolymerized polypyrrole thin films onto interdigitated microsensor electrode arrays

Synthesis and characterization of nanostructured polypyrroles: Morphology-dependent electrochemical responses and chemical deposition of Au nanoparticles

Synthesis, characterization, and efficient electrohydrodynamic patterning with a high aspect ratio of a soluble oligomerpyrrole derivative

Electrochemical deposition of conductive and adhesive polypyrrole-dopamine films

Interface Effect on the Electropolymerized Polypyrrole Films with Hollow Micro/Nanohorn Arrays

Preparation, Characterization and Electrochemical Properties of Polypyrrole-Polystyrene Sulfonic Acid Composite Film

Electropolymerization of Polypyrrole on PFIL–PSS-modified Electrodes Without Added Support Electrolytes