Abstract:The intermediate temperature deformation behavior and microstructural evolution of a spray formed 7075 Al alloy were performed at temperatures 60–120 °C with strain rates 0.00001–0.1 s −1 . The results reveal that the softening mechanism of the intermediate temperature deformation is dynamic recovery (DRV), which can be quantitated by Zener-Hollomon ( Z ) parameter. The constitutive equation can reasonably predict the stress-strain behavior of the alloy at intermediate temperatures. The activation energy is related to the deformation process and the interactions of the substructure, the average value is 140.1 kJ/mol. The higher efficiency of power dissipation in the processing map is related to the DRV at lower deformation temperatures. The optimum processing domain is located at the temperature of 90–120 °C and strain rate of 0.006–0.1 s −1 with a power dissipation efficiency range of 20%–40%. The processing parameters of the intermediate temperature deformation should be strictly controlled according to the strain. The uniform microstructure of 7075 alloys obtained by spray forming is crucial to overcome the disadvantage of poor deformability. The inferior coordinated deformation facilitates crack propagation at low strain rates. The high-density dislocation provides adequate nucleation sites for dynamic precipitation. The level of dynamic restoration facilitates the transformation from low angle grain boundaries (LAGBs) to high angle grain boundaries (HAGBs). The dislocations move to the grain/sub-grain boundary to form dislocation walls at low temperatures. The contribution to the stress from grain boundary (13.2–17.7 MPa), nanoscale precipitates (65.7–191.5 MPa), and dislocation (5.9–23.4 MPa) increases the difficulty of deformation. The deformation process at higher temperatures (105–120 °C) can be facilitated by the dissolution and coarsening of the nanoscale precipitates, and dislocation motion at the grain boundary.

Microstructure and Mechanical Properties of 7055 Al Alloys by Spray Forming

Microstructure and Mechanical Properties of 7475 Aluminum Alloy by Spray Forming

Effect of heat treatment and extrusion processing on the microstructure and mechanical properties of spray formed 7055 alloy

Effects of Hot Extrusion and Heat Treatment on Microstructure and Properties of Industrial Large-Scale Spray-Deposited 7055 Aluminum Alloy

Suppress Defect-Induced Plastic Instability to Achieve Superior Strength-Ductility Combination of Spray Formed 7050 Al Alloy

Study on Microstructure and Mechanical Properties of A356 Aluminum Alloy by Spray Forming

Microstructures and tensile properties of spray-deposited high-strength aluminium alloys

Hot Workability and Dynamic Recrystallization Behavior of a Spray Formed 7055 Aluminum Alloy

Microstructures and Mechanical Properties of High Strength AZ91 Mg Alloy by Spray Forming Technology

Intermediate temperature tensile behavior and processing map of a spray formed 7075 aluminum alloy

The effects of heat treatment on the extrusion-induced inhomogeneity of spray-formed aluminum alloy 7055

Extrusion Processing of High-Strength Al Alloy 7055

Microstructure Evolution Behavior of Spray-Deposited 7055 Aluminum Alloy during Hot Deformation

Characterization of Hot Extrusion and Heat Treatment on Mechanical Properties in a Spray Formed Ultra-High Strength Al-Zn-Mg-Cu Alloy

Precipitation behavior of spray-formed aluminum alloy 7055 during high temperature aging

Solid-state Additive Manufacturing High Performance Aluminum Alloy 6061 Enabled by an In-Situ Micro-Forging Assisted Cold Spray

Microstructure and Mechanical Properties of Thixoforming 6066Al by Spray Deposition

Microstructure and Properties of 50si50al Alloy by Spray Forming

Microstructure and Mechanical Properties of Spray Formed 7055 Aluminum Alloy by Underwater Friction Stir Welding

Effect of Hot Deformation and Heat Treatment on the Microstructure and Properties of Spray-Formed Al-Zn-Mg-Cu Alloys

Effect of pretreatment on microstructural stability and mechanical property in a spray formed Al-Zn-Mg-Cu alloy