Abstract:Low-cycle fatigue (LCF) behavior of nickel-based precipitation-strengthened superalloy GH4145/SQ was investigated systematically under fully reversed total strain amplitude control conditions at 538°C in laboratory air. It was shown that the alloy exhibited a pronounced initial fatigue hardening followed by continuous fatigue softening to failure at high strain amplitudes, while at low strain amplitudes the initial hardening was followed by a well-defined saturation stage. Microstructure observations using optical and transmission-electron microscopy revealed that slip band density increased with increasing total strain amplitudes and the size of the γ′precipitates tended to reduction due to repeated shearing by the dislocations with continuous cyclic straining. The above changes in microstructures during cycling were essentially responsible for the fatigue hardening–softening behavior of the alloy. Both optical and SEM micrographs indicated that at low strain amplitudes crack propagation was basically transgranular, while at high strain amplitudes crack propagation was essentially intergranular. Bilinear behavior with a change of slope at a plastic strain amplitude of about 0.2pct was observed in cyclic stress–strain (CSS), Coffin–Manson (C–M) and plastic strain energy–life plots. A change in the number of operating slip systems and the fracture modes with the strain amplitude employed was used to explain this two-slope characteristic. In both the companion specimens test (CST) and the incremental step test (IST) methods the alloy exhibited non-masing type behavior. It was suggested that, for the first approximation, the half-life plastic strain energy could be calculated directly according to the equation without reckoning in the non-masing behavior.

Failure Behavior of Ultra-high Cycle Fatigue of a 2 000 MPa Grade High Strength Steel

Low cycle fatigue behavior of nickel-based superalloy GH4145/SQ at elevated temperature

High-Cycle Fatigue Fracture Behavior of Ultrahigh Strength Steels

Dependence of Fatigue Strength on Inclusion Size for High-Strength Steels in Very High Cycle Fatigue Regime

Influence of Inclusion Size on Fatigue Behavior of High Strength Steels in the Gigacycle Fatigue Regime

GIGACYCLE FATIGUE OF ULTRA-HIGH STRENGTH STEELS

Low Cycle Fatigue Behavior of Original Ferritic P92 Steel at High Temperature: Experiments and Simulations

Low Cycle Fatigue and Creep Fatigue Interaction Behavior of 9Cr-0.5Mo-1.8w-v-nb Heat-Resistant Steel at High Temperature

Study on Inclusion Induced Fatigue Crack Initiation and Propagation in Ultra-High Strength Steel for Aerospace Application

Characterization of Low Cycle Fatigue Performance of New Ferritic P92 Steel at High Temperature: Effect of Strain Amplitude

Abnormal Relation Between Tensile and Fatigue Strengths for a High-Strength Low-Alloy Steel

Ultra High Cycle Fatigue Behavior of Automotive High Strength Spring Steels 54sicrv6 and 54Sicr6

Fatigue fracture behaviour of a medium-carbon 2 000 MPa level high strength spring steel

The Effect of Inclusions on the Fatigue Behavior of Fine-Grained High Strength 42crmovnb Steel

Influence of Non-Metallic Inclusions on Very High-Cycle Fatigue Performance of High-Strength Steels and Interpretation via Crystal Plasticity Finite Element Method

Comparative Study of High-Cycle Fatigue and Failure Mechanisms in Ultrahigh-Strength CrNiMoWMnV Low-Alloy Steels

The Fatigue Behaviors of Zero-Inclusion and Commercial 42crmo Steels in the Super-Long Fatigue Life Regime

Gigacycle Fatigue Behavior of 1800 MPa Grade High Strength Spring Steel for Automobile Lightweight

FATIGUE PROPERTY OF ULTRA-LONG LIFE OF HIGH STRENGTH 42crmo ZERO-INCLUSION STEEL

Fatigue limit evaluation via infrared thermography for a high strength steel with two strength levels

Effect of Inclusion Size on High-Cycle Fatigue Behavior of High Strength Spring Steel