Abstract:Herein, highly transparent and conductive In2O3 films were deposited by reactive high power impulse magnetron sputtering from a metal target without thermal assistance. Film deposition was performed at room temperature using oxygen flow rates selected based on target voltage hysteresis, and the obtained films were compared in terms of structure and electrical/optical properties. Notably, the use of high plasma density, peak power, and ionization efficiency resulted in the formation of highly crystalline films featuring a small grain size and a columnar structure with a preferred orientation. The minimal carrier concentration of 1.6 × 1021 cm−3 was observed for films deposited in metallic mode; the carrier mobility of these films increased from 23 to 51 cm2 V−1 s−1 as the oxygen flow rate increased from 7 to 10 sccm. Moreover, the oxygen flow rate significantly affected the conductivity of In2O3 films, which ranged from semiconductor-like to insulator. The visible-light transmittance of In2O3 films exceeded 85% when oxygen flow rate larger than 7sccm. The absorption edge of as-prepared films was located close to 350 nm and shifted to lower wavelengths with increasing oxygen flow rate, which was explained by the Burstein–Moss effect. The infrared transmittance of In2O3 films was strongly dependent on the deposition mode. In agreement with Drude's theory, films deposited in transition mode at room temperature were highly transparent and conductive, which was ascribed to the use of controlled In:O ratios, whereas films deposited in other modes were shown to exhibit either excellent conductivity (metallic mode) or good optical transmittance (poisoning mode).

Flexible and Transparent Conducting CdO Films Deposited by RF Magnetron Sputtering

Low Resistivity Transparent Conducting CdO Thin Films Deposited by DC Reactive Magnetron Sputtering at Room Temperature

Microstructure and Optical Properties of ZnO Films Deposited by Radio-frequency Reactive Magnetron Sputtering

Deposition and Characterization of AZO Thin Films on Flexible Glass Substrates Using DC Magnetron Sputtering Technique

Transparent conductive F-doped SnO 2 films prepared by RF reactive magnetron sputtering at low substrate temperature

Deposition of Transparent Conducting CdO on Flexible PET Substrate

Structural ,Electrical ,and Optical Properties of Transparent Conductive Al-Doped ZnO Films Prepared by RF Magnetron Sputtering

Transparent Conductive Cu-In-O Thin Films Deposited by Reactive Dc Magnetron Sputtering with Different Targets

Modulation of optical and electrical properties of In2O3 films deposited by high power impulse magnetron sputtering by controlling the flow rate of oxygen

High Mechanical Stable Flexible Transparent Conductive In-doped CdO Thin Film Deposited at Low Temperature on PET Substrate

Performance Study of AZO/Ag/AZO Transparent Conductive Multilayer Prepared Films by R.F Magnetron Sputtering

Cu–In–O composite thin films deposited by reactive DC magnetron sputtering

The structural, electrical, and optical properties of SnO2 films prepared by reactive magnetron sputtering: Influence of substrate temperature and O2 flow rate

Electrochromic Properties and Performance of NiOx Films and Their Corresponding All-Thin-film Flexible Devices Preparedby Reactive DC Magnetron Sputtering

Growth and Properties of Transparent Conductive ZnO∶Al Films by Magnetron Sputtering at Low Temperature

Structure and Transparent Conductive Properties of SnO2 and SnO2:F Films Deposited by RF Reactive Magnetron Sputtering

Transparent Conducting Antimony-Doped Tin Oxide Films Deposited on Flexible Substrates by R.f. Magnetron-Sputtering

Structural, Optical and Electrical Properties of Al-Zr Codoped ZnO Transparent Conductive Thin Films

Properties of transparent conductive ZnO:Al thin films prepared by magnetron sputtering

Highly Transparent and Conducting Cdo Films Grown by Chemical Spray Pyrolysis

The effect of oxygen on the properties of transparent conducting Cu–Al–O thin films deposited by rf magnetron sputtering