Abstract:Legislations concerning emissions from heavy-duty diesel engines are becoming increasingly stringent. This requires conventional diesel combustion to be compliant using costly and sophisticated aftertreatment systems. Preferably, diesel–methanol dual-fuel is one of the suitable alternative combustion modes as it can potentially reduce the formation of nitrogen oxide and soot emissions which characterised the diesel mixing-controlled combustion. This is primarily due to the high latent heat of vaporisation and oxygen content of the methanol fuel. At high engine loads, however, the potential of diesel–methanol dual-fuel operation is constrained by the excessive combustion pressure rise rate and peak in-cylinder pressure, which limits both the engine efficiency and the percentage of methanol that can be used. For the first time, experimental studies were conducted to explore advanced combustion control strategies such as Miller cycle, exhaust gas recirculation, and intake air cooling for improving upon high load diesel–methanol dual-fuel combustion. Experiments were carried out at 1200 r/min and 18 bar indicated mean effective pressure on a single-cylinder heavy-duty diesel engine, which equipped with a high pressure common rail diesel injection, a methanol port fuel injection, and a variable valve actuation system on the intake camshaft. Results showed that the methanol energy fraction of a conventional diesel–methanol dual-fuel operation with a baseline intake valve closing timing was limited to 28%. This was due to the high combustion temperature at a high load which advanced the ignition timing of the premixed charge, resulting in high levels of pressure rise rate. The application of lower effective compression ratio and intake air temperature ( T int ) effectively decreased the compression temperature, which successfully delayed the ignition timing of the premixed charge. This allowed for a more advanced diesel injection timing to achieve improvement in the thermal efficiency and potentially enabled a higher methanol substitution ratio. Although the introduction of exhaust gas recirculation demonstrated very slight impact on the ignition timing of the premixed charge, a higher net indicated efficiency was observed due to a relatively lower local combustion temperature which reduced heat transfer loss. Moreover, the optimised diesel–methanol dual-fuel operation allowed a higher methanol energy fraction of 40% to be used at an effective compression ratio of 14.3 and T int of 305 K and achieved the highest net indicated efficiency of 47.4%, improving by 3.7% and 2.6%, respectively, when compared to the optimised conventional diesel combustion (45.7%) and conventional diesel–methanol dual-fuel (46.2%). This improvement was accompanied with a reduction of 37% in nitrogen oxide emissions and little impact on soot emissions in comparison with the conventional diesel combustion.

Mechanism of Diesel Fuel Burning in Methanol Mixture with High Efficiency and Low Emission

Engine Performance and Emissions of A Compression Ignition Engine Operating on the Diesel-Methanol Blends

Combustion and Emission Characteristics of a DI Diesel Engine Fueled by Diesel-Methanol Blends

Exploring the high load potential of diesel–methanol dual-fuel operation with Miller cycle, exhaust gas recirculation, and intake air cooling on a heavy-duty diesel engine

To achieve high methanol substitution ratio and clean combustion on a diesel/methanol dual fuel engine: A comparison of diesel methanol compound combustion (DMCC) and direct dual fuel stratification (DDFS) strategies

Effect of injection strategy on a diesel/methanol dual-fuel direct-injection engine

Optimization of methanol/diesel dual-fuel engines at low load condition for heavy-duty vehicles to operated at high substitution ratio by using single-hole injector for direct injection of methanol

Study on Combustion Characteristics of a DI Diesel Engine Operating on Diesel/Methanol Blends

Improving the lean burn performance of a high compression ratio methanol engine by multiple-injection

Effects of Methanol Addition on the Combustion Process of the Methanol/Diesel Dual-Fuel Based on an Optical Engine

Combustion and Emission Characteristics of Methanol–Diesel Dual Fuel Engine at Different Altitudes

Experimental study on effects of pilot injection strategy on combustion and emission characteristics of diesel/methanol dual-fuel engine under low load

Experimental investigations of the effects of pilot injection on combustion and gaseous emission characteristics of diesel/methanol dual fuel engine

The mechanism of the increased ratio of nitrogen dioxide to nitrogen oxides in methanol/diesel dual fuel engines

A comparative study on operating range and combustion characteristics of methanol/diesel dual direct injection engine with different methanol injection timings

Diesel/methanol dual-fuel combustion: An assessment of soot nanostructure and oxidation reactivity

Study on the Performance of Diesel-Methanol Diffusion Combustion with Dual-Direct Injection System on a High-Speed Light-Duty Engine

Multi-objective optimization of a compression ignition engine using on-board methanol reforming

Effects of fuel injection timings and methanol split ratio in M/D/M strategy on a diesel/methanol dual-fuel direct injection engine

The Effect of Methane Addition on the Low-Temperature Oxidation Preparation and the Thermal Ignition Preparation of Dimethyl Ether under Representative Engine In-Cylinder Thermal Conditions

Numerical Investigation on the Influence of Injection Location and Injection Strategy on a High-Pressure Direct Injection Diesel/Methanol Dual-Fuel Engine