Abstract:An electrochemical carbon nanotube filter has been reported to be effective for the removal and electrooxidation of aqueous chemicals and microorganisms. Here, we investigate how carbon nanotube (CNT) chemical surface treatments including calcination to remove amorphous carbon, acid treatment to remove internal residual metal oxide, formation of surficial oxy-functional groups, and addition of Sb-doped SnO(2) particles affect the electrooxidative filter performance. The various CNT samples are characterized by scanning electron microscopy (SEM), thermogravimetric analysis (TGA), and X-ray photoelectron spectroscopy (XPS) and electrochemically evaluated by cyclic voltammetry, open circuit potential versus time analysis, and electrochemical impedance spectroscopy. Voltammetry results indicate that the near CNT surface pH is at least two units lower than the bulk pH. The electrooxidative performance of the various CNT samples is evaluated with 1 mM of methyl orange (MO) in 100 mM sodium sulfate at a flow rate of 1.5 mL min(-1). At both 2 and 3 V, the efficacy of electrochemical filtration is observed to be function of CNT surface chemistry. The samples with the greatest electrooxidation were the calcinated then HCl-treated CNTs, i.e., the CNTs with the most surficial sp(2)-bonded carbon, and the Sb-SnO(2)-coated CNTs, i.e., the CNTs with the most electrocatalytic surface area. At 3 V applied voltage, these CNT samples are able to oxidize 95% of the influent MO within the liquid residence time of <1.2 s. The broader applicability of electrochemical filtration is evaluated by challenging the C-CNT-HCl and C-CNT-HNO(3) networks with various organics including methylene blue, phenol, methanol, and formaldehyde. At 3 V applied voltage, both CNTs are able to degrade a fraction of all the organics with the extent organic degradation dependent on both CNT and organic properties. The C-CNT-HCl network generally had the better oxidative performance than the C-CNT-HNO(3) network with an exception being the positively charged methylene blue. The extent of MO degradation, steady-state current, anode potential, effluent pH, and back pressure are also measured as a function of applied voltage (1-3 V) and CNT surface chemistry. Mass spectrometry of electrochemical CNT filter effluent at 2 and 3 V is utilized to evaluate plausible electrooxidation products. Energy consumption as compared to state-of-the-art electrodes and strategies to tailor the CNT surface for a specific target molecule are discussed.

UNUSUAL ELECTROCHEMICAL RESPONSE OF ELECTROCHEMICAL ETCHING ON MULTIWALLED CARBON NANOTUBES

Synergy Between Structure Characteristics and the Solution Chemistry in a Near/Non-Equilibrium Oxidative Etching of Penta-Twinned Palladium Nanorods

Selective Electrochemical Etching of Single‐Walled Carbon Nanotubes

Fabrication and Electrochemical Characterization of Multi-Walled Carbon Nanotubes Film on a Titanium Mesh Electrode

Nanomanufacturing of Multi-Walled Carbon Nanotubes Enhanced Electrochemical Electrode Through Surface Micromachining

Real-Time Observation of Carbon Nanotube Etching Process Using Polarized Optical Microscope.

Electrochemical Carbon Nanotube Filter Oxidative Performance As A Function of Surface Chemistry

Electrochemical Carbon Nanotube Filter for Adsorption, Desorption, and Oxidation of Aqueous Dyes and Anions

Tailoring the Atomic‐Local Environment of Carbon Nanotube Tips for Selective H2O2 Electrosynthesis at High Current Densities

Study on preparation and electrochemistry sensitivity of the carbon nanotubes modified electrode

Carbon Nanotubes As Electrode Modifier Promoting Direct Electron Transfer from Shewanella Oneidensis.

Investigation on the Electrochemical and Electrocatalytic Behavior of Chemically Modified Electrode of Single Wall Carbon Nanotube Functionalized with Carboxylic Acid Group

Electrocatalytic Properties Improvement on Carbon-Nanotubes Coated Reaction Surface for μDMFC

Abrasively Immobilised Multiwalled Carbon Nanotube Agglomerates: a Novel Electrode Material Approach for the Analytical Sensing of Ph.

Selectively attaching Pt-nano-clusters to the open ends and defect sites on carbon nanotubes for electrochemical catalysis

Application of multi-walled carbon nanotubes modified with boron oxide nanoparticles in electrochemistry

Investigation of the Electrochemical and Electrocatalytic Behavior of Single-Wall Carbon Nanotube Film on a Glassy Carbon Electrode

Electrochemical Durability Investigation of Single-Walled and Multi-Walled Carbon Nanotubes under Potentiostatic Conditions

Investigation of Etching Behavior of Single-Walled Carbon Nanotubes Using Different Etchants

Single-walled Carbon Nanotubes Wrapped with Charged Polysaccharides Enhance Extracellular Electron Transfer

Electrochemical Functionalization of Single-Walled Carbon Nanotubes in Large Quantities at a Room-Temperature Ionic Liquid Supported Three-Dimensional Network Electrode