Abstract:The inherent disadvantages of carbon-based anodes, including their low hydrophilicity, significant charge transfer resistance, and limited power density, hinder their widespread commercial utilization in microbial fuel cells (MFC). Addressing these challenges, this study involved the surface modification of a carbon-based anode. To improve the adhesion of electroactive microorganisms (EAM) on the anode surface and increase the extracellular electron transfer rate, CNT@Ti 3 C 2 T x MXene was applied to the surface of carbon cloth (CC) using drip coating. Initially, we conducted a comprehensive investigation on the optimal amount of modification required. To achieve this, we designed four distinct groups of modified electrodes. Through electrochemical analysis and phase characterization, it was determined that a modification dosage of 1.5 mg/cm 2 for CNT@Ti 3 C 2 T x MXene/CC electrodes yielded the most optimal electrical conductivity and the highest capacitance. The Rs of CC is reduced from 1.48 to 0.55 Ω and the Rct from 2.62 to 2.09 Ω, and the capacitance is increased from 3.98 10 −07 F to 9.11 10 −06 F . Subsequently, the CNT@Ti 3 C 2 T x MXene/CC with a modification of 1.5 mg/cm 2 was used as the anode of the microbial fuel cell. The modification of CNT@Ti 3 C 2 T x MXene improved the power generation performance. The maximum output voltage of the MFC was increased from 546 to 709 mv, and the power density was increased from 44.9 to 101.8 mW/m 2 . The underlying factor lies in the ability of CNT@Ti 3 C 2 T x MXene/CC to significantly lower the internal resistance within the microbial fuel cell, thereby fostering the development of biofilm. Notably, our observations revealed that the biofilm formation was particularly facilitated on the anode surface of CNT@Ti 3 C 2 T x MXene/CC. In essence, the CNT@Ti 3 C 2 T x MXene-modified carbon cloth not only minimizes internal resistance but also enhances the electroactive surface area, exhibiting superior electrical conductivity. These attributes make it an advantageous material for biological applications.

Electrocatalytic Properties Improvement on Carbon-Nanotubes Coated Reaction Surface for μDMFC

Electrocatalytic properties improvement on carbon-nanotubes coated reaction surface for micro-DMFC

Preparation and Characterization of the Carbon Nano Tubes Supporting Oxygen Electrode Material for PEMFC

Preparation, Structure and Electrochemical Hydrogenation of Carbon Nanotubes Supported Platinum Catalysts

Highly Efficient CO2 Bubble Removal on Carbon Nanotube Supported Nanocatalysts for Direct Methanol Fuel Cell

Uniform Nafion ® coated HRA anode for high performance micro DMFC

Electro-catalytic Oxidation of CO on Pt Catalyst Supported on Carbon Nanotubes Pretreated with Oxidative Acids

Carbon nanotube powders as electrode modifier to enhance the activity of anodic biofilm in microbial fuel cells.

Uniform Nafion

High Performance Nanocatalysts Supported on Micro/Nano Carbon Structures Using Ethanol Immersion Pretreatment for Micro Dmfcs

Electrospinning-Derived Carbon Fibrous Mats Improving the Performance of Commercial Pt/C for Methanol Oxidation

CNT@Ti3C2TxMXene Nanocomposite Catalysts as Anodes to Improve the Electricity Production Performance of Microbial Fuel Cells

Uniform Nafion (R) Coated Hra Anode For High Performance Micro Dmfc

Enhanced Performance of Nitrogen-Doped Carbon Nanotube Membrane-Based Filtration Cathode Microbial Fuel Cell

Curvature Effect of Pyridinic N-Modified Carbon Atom Sites for Electrocatalyzing CO2 Conversion to CO.

Growth and characteristics of vertically-aligned carbon nanotubes by thermal CVD on various Si-based substrates for micro-DMFC

Electrochemical investigation on addition of CNTs to the positive electrodes for Ni/MH rechargeable batteries

Electrochemical Investigation of Carbon Nanotubes as Additives in Positive Electrodes of Ni∕MH Batteries

Effect of Extremely Short-Sized MWCNT as Additive Material in High Surface Area Activated Carbon and Its Enhanced Electrical LIC Performance

Pt Nanoclusters Electrodeposited on Single-Walled Carbon Nanotubes for Electrochemical Catalysis

Enhanced Catalytic Properties from Platinum Nanodots Covered Carbon Nanotubes for Proton-Exchange Membrane Fuel Cells