Biodegradable Blends of Polycaprolactone with Thermoplastic Starch
Gang Li
2010-01-01
Abstract:RESUME Ce travail presente une approche pour la preparation de melanges polycaprolactone (PCL)/amidon thermoplastique (TPS) par extrusion en une seule etape. La mise en oeuvre en une etape a l’etat fondu de melanges polymeres a base d’amidon thermoplastique est une operation complexe impliquant la plastification, la devolatilisation, le melange a l’etat fondu et le controle de la morphologie. Tout ceci doit etre complete en un temps de residence total d’au plus deux minutes dans une extrudeuse. Afin de determiner les limites de temps/temperature requises pour plastifier avec succes l’amidon dans un environnement de mise en oeuvre de polymeres a l’etat fondu, la calorimetrie par balayage differentiel (DSC), la microscopie optique et la diffraction de rayons X a grand angle (WAXS) ont ete utilisees pour etudier les aspects cles de la gelification de l’amidon dans des melanges glycerol/eau en exces. En meme temps, ces resultats ont ete lies a la morphologie de melanges a l’etat fondu d’amidon thermoplastique (TPS) et de polycaprolactone (PCL). Dans un deuxieme temps, le developpement de la morphologie et les interactions interfaciales dans les melanges PCL/TPS ont ete etudies. Finalement, la biodegradation d’amidon natif, d’amidon thermoplastique (TPS) a haute teneur en glycerol, et de leurs melanges avec du polyethylene a basse densite (LDPE) et du poly(acide lactique) (PLA) a ete demontree sous des conditions de compostage.----------ABSTRACT This work presents an approach to preparing polycaprolactone (PCL)/thermoplastic starch (TPS) blends via a one-step extrusion approach. The one-step melt processing of polymer blends with thermoplastic starch is a complex operation involving plasticization, devolatilization, melt-melt mixing and morphology control. All this must be achieved within a maximum two minutes total residence time in an extruder. In addition, starch is a complex natural polymer and thus gelatinization is a delicate process. In order to determine the time/temperature boundaries ultimately required for the successful plasticization of starch in a polymer melt processing environment, differential scanning calorimetry (DSC), optical microscopy and wide angle X-ray diffraction (WAXD) were used to examine the critical aspects of starch gelatinization in glycerol/excess water mixtures. Simultaneously, these results were related to the morphology of melt-blended thermoplastic starch (TPS) in polycaprolactone (PCL). Secondly, the morphology development and interfacial interactions in PCL/TPS blends were studied. Finally, the biodegradation of native starch, thermoplastic starch (TPS) containing high concentration of glycerol, and its blends with low-density polyethylene (LDPE) and polylactic acid (PLA) were demonstrated under compost conditions. In the first part of the work, starch gelatinization was examined in detail. The onset and conclusion temperatures for wheat starch gelatinization were obtained via differential scanning calorimetry (DSC), X-ray diffraction and polarized light microscopy. The results indicate that water and glycerol exhibit significantly different effects on the starch gelatinization temperature. With a constant concentration of glycerol related to dry starch, the onset, To, peak, Tp,and conclusion, Tc, gelatinization temperatures all shift to low temperatures with increasing water concentration. Conversely, these gelatinization temperatures shift to high temperatures when the water concentration is held constant and the quantity of glycerol is increased. In both cases, the gelatinization endotherm becomes more pronounced with increasing plasticizer concentration in the system. These results are very useful to set up the extrusion temperatures since the gelatinization temperature can be changed by varying the ratio of water and glycerol in initial starch/water/glycerol mixtures.