Abstract:Two promising high-entropy alloys (HEAs) AlxCrFe1.5MnNi0.5 (x = 0.3 and 0.5) were designed from Al–Co–Cr–Cu–Fe–Ni alloys by substituting Mn for expensive Co and excluding Cu to avoid Cu segregation. Microstructures and properties were investigated and compared at different states: as-cast, as-homogenized, as-rolled and as-aged states. Al0.3CrFe1.5MnNi0.5 alloy in the as-cast, as-homogenized and as-rolled states has a dual-phase structure of BCC phase and FCC phase, in which Al, Ni-rich precipitates of B2-type BCC structure disperse in the BCC phase. Al0.5CrFe1.5MnNi0.5 alloy in the corresponding states has a matrix of BCC phase in which Cr-rich particles of BCC structure and Al, Ni-rich precipitates of B2-type BCC structure disperse. These three BCC phases have the same lattice constant. Both alloys are workable and show a hardness range of Hv 300–500 in the as-cast, as-forged, as-homogenized and as-rolled states. Al0.5CrFe1.5MnNi0.5 alloy has a higher hardness level than Al0.3CrFe1.5MnNi0.5 one because of its full BCC phase. Both alloys thus can be used as structural parts requiring stronger strength. Both alloys display a significant high-temperature age-hardening phenomenon. As-cast Al0.3CrFe1.5MnNi0.5 alloy can attain the highest hardness, Hv 850, at 600 °C for 100 h, and Al0.5CrFe1.5MnNi0.5 can get even higher hardness, Hv 890. The aging hardening is resulted from the formation of ρ phase (Cr5Fe6Mn8-like phase). Prior rolling on the alloys before aging could significantly enhance the age-hardening rate and hardness level due to introduced defects. Al0.5CrFe1.5MnNi0.5 alloy exhibits excellent oxidation resistance up to 800 °C, which is better than Al0.5CrFe1.5MnNi0.5 alloy. Combining this merit with its high softening resistance and wear resistance as compared to commercial alloys Al0.5CrFe1.5MnNi0.5 alloy has the potential for high-temperature structural applications.

Microstructure and mechanical performance of new Al0.5CrFe1.5MnNi0.5 high-entropy alloys improved by plasma nitriding

Microstructures and Mechanical Performance of Plasma-Nitrided Al0.3crfe1.5mnni0.5 High-Entropy Alloys

Effect of Aluminum Content on Plasma-Nitrided Al X CoCrCuFeNi High-Entropy Alloys

Microstructure and Mechanical Performance of Brand‐New Al0.3CrFe1.5MnNi0.5 High‐Entropy Alloys

Microstructural Evolution and Elevated-Temperature Strengthening Mechanism of Co-free FeCrMnNiV0.2Alx High-Entropy Alloys During Annealing

Enhancing the Strength of AlCrFeNi HEAs Via Tailoring Aluminum Content and Optimal Aging Treatment

Microstructure and wear properties of nitrided AlCoCrFeNi high-entropy alloy

Improved tribological behavior of plasma-nitrided AlCrTiV and AlCrTiVSi high-entropy alloy films

Effect of Al content on microstructure and wear properties of FeCrNiMnAlx high-entropy alloys

An effective and innovative application of rare-earth plasma nitriding on high entropy alloy CoCrCuFeNi

Microstructure and Properties of Age-Hardenable AlxCrFe1.5MnNi0.5 Alloys

Microstructure and Friction Properties of AlCrTiVNbx High-Entropy Alloys via Annealing Manufactured by Vacuum Arc Melting

An investigation on nitrogen uptake and microstructure of equimolar quaternary FeCoNiCr high entropy alloy after active-screen plasma nitriding

Microstructure, mechanical and corrosion performance of magnetron sputtered (Al0.5CoCrFeNi)Nx high-entropy alloy nitride films

Effects of nitrogen content on microstructures and mechanical properties of (AlCrTiZrHf)N high-entropy alloy nitride films

Effect of nitrogen on microstructure and mechanical properties of CrMnFeVTi6 high entropy alloy

Microstructure, Mechanical Property, and Wear Behavior of NiAl-Based High-Entropy Alloy

Aluminum-Modified Plasma Nitriding with High Efficiency and Enhanced Performance

Microstructure and Properties of FeCrMnxAlCu High-Entropy Alloys and Coatings

Microstructure evolution and properties of Fe-Ni-Cr-Co-Mo-W high-entropy alloy coatings by plasma surface alloying technology

Wear and high-temperature oxidation resistance of (AlCrFeTiV)100-xNix high-entropy alloy coatings prepared by laser cladding on Ti6Al4V alloy