Abstract:Concrete-infilled double steel corrugated-plate walls (CDSCWs) are composed of two steel corrugated-plates (SCPs) which are connected through bolts, and concrete filled the spacing formed between the two SCPs. Two vertical boundary elements are installed additionally at both sides of CDSCWs. On the one hand, the corrugated configuration of SCPs has great improvement on the load-bearing efficiency of CDSCWs; on the other hand, much higher bearing capacities and better seismic performance for CDSCWs are provided owing to the interactions among SCPs, bolts and infilled-concrete. This paper investigates the load-bearing mechanism and strength design formulae of CDSCWs under compressions. Since SCPs are prone to local buckling failure between two rows of bolts under the conditions of large vertical bolt spacing and small thickness of SCPs, this paper mainly focuses on the load-bearing mechanism of SCPs in CDSCWs under uniform compressions. The unilateral constraint on SCPs provided from infilled-concrete and the restraining effect on the flexural deformation of SCPs owing to bolts are considered. At first, series of finite element (FE) eigenvalue buckling analyses are conducted to study the elastic buckling behavior of SCPs subjected to uniform compressions. On the basis of Euler's formula, the formulae for predicting the elastic buckling stresses and corresponding normalized slenderness ratios λs of SCPs are achieved respectively. The instability performance of SCPs under uniform compressions is then investigated through FE nonlinear analyses, and accordingly the stability coefficient φs is attained. The corresponding φs−λs curve is therefore established in order to calculate the ultimate bearing capacities of SCPs. In addition, the cooperative performance of material strengths between SCPs and concrete is analyzed numerically when CDSCWs reach their compressive ultimate strength. With this consideration, the design method for predicting the cross-sectional strength of CDSCWs under compressions is proposed. Moreover, a CDSCW specimen with I-section is tested under a compressive load. Its cross-sectional strength is investigated experimentally. The results of the experiment coincide with those of numerical simulation, this verifying the safety and validity of the design method for cross-sectional strength design of CDSCWs.

Design of strengthening columns in the ground floor of a frame-shear wall structure

Seismic Behavior of Composite Shear Walls Incorporating Concrete-Filled Steel and FRP Tubes As Boundary Elements

Experimental study and numerical simulation of seismic performance of stiffened thin steel plate shear walls considering the effect of vertical load on frame column

The Strong Column–weak Beam Design Philosophy in Reinforced Concrete Frame Structures: A Literature Review

Seismic Behaviors of High-Strength Bolted End-Plate Connected Composite Steel Beam and Square Concrete Filled Steel Tube Column Frames

EXPERIMENTAL STUDY ON THE SEISMIC BEHAVIOR OF CFST RECTANGULAR COLUMN TO H-SECTION STEEL BEAM CONNECTIONS WITH EXTERNAL STIFFENERS

Discussion of Strengthening Method Based on the Current Damage of a Concrete Frame-Shear Wall Structure

Experimental investigation of concrete-filled steel tubular columns with reinforcing lattice angle

STUDY ON WEAK BEAM-STRONG COLUMN DESIGN METHOD OF RC FRAME STRUCTURES

STRONG-COLUMN WEAK-BEAM GLOBAL SEISMIC FAILURE MODE CONTROL-BASED DESIGN OF REINFORCED CONCRETE FRAME STRUCTURES

Comparison and Optimization of Influence of Reinforcement Ratio on Deformation and Ductility of Short-leg Shear Wall

Structure Strenghtening Design with Adding Storey of Beijing International Financial Center

Realization of Strong Column-Weak Beam Failure Mode for Concrete-Filled Square Steel Tubular Frame Structure

Experimental study on seismic behavior of high-strength concrete filled double-steel-plate composite walls

Experimental study on seismic performance of ultra high-strength concrete short columns

FINITE ELEMENT SIMULATION ON THE ENTIRE MECHANICAL PERFORMANCE OF T-SHAPED SHORT-LEG CONCRETE SHEAR WALLS UNDER STATIC LOADING FROM ELASTIC TO COLLAPSE STAGES

Strength Design of Concrete-Infilled Double Steel Corrugated-Plate Walls under Uniform Compressions

Research on Weak Beam-strong Column Design Method of Steel-concrete Composite Frame Structures

Ultimate strength and design of CFDST columns with intermittent welded plate stiffeners

Experimental Study on Both Sides Strengthening of Low-reinforced Shear Wall

Experimental Study on Seismic Strengthening of RC Columns with Wrapped CFRP Sheets