Abstract:Background: Orbital floor fractures (OFFs) represent an interesting chapter in maxillofacial surgery, and one of the main challenges in orbit reconstruction is shaping and cutting the precise contour of the implants due to its complex anatomy. Objective: The aim of the retrospective study was to demonstrate, through pre- and postoperative volumetric measurements of the orbit, how the use of a preformed titanium mesh based on the stereolithographic model produced with 3D printers ("In-House" reconstruction) provides a better reconstruction volumetric compared to the intraoperatively shaped titanium mesh. Materials and Methods: The patients with OFF enrolled in this study were divided into two groups according to the inclusion criteria. In Group 1 (G1), patients surgically treated for OFF were divided into two subgroups: G1a, patients undergoing orbital floor reconstruction with an intraoperatively shaped mesh, and G1b, patients undergoing orbital floor reconstruction with a preoperative mesh shaped on a 3D-printed stereolithographic model. Group 2 (G2) consisted of patients treated for other traumatic pathologies (mandible fractures and middle face fractures not involving orbit). Pre- and postoperative orbital volumetric measurements were performed on both G1 and G2. The patients of both groups were subjected to the measurement of orbital volume using Osirix software (Pixmeo SARL, CH-1233 Bernex, Switzerland) on the new CT examination. Both descriptive (using central tendency indices such as mean and range) and regressive (using the Bravais–Pearson index, calculated using the GraphPad program) statistical analyses were performed on the recorded data. Results: From 1 January 2017 to 31 December 2021, of the 176 patients treated for OFF at the "Magna Graecia" University Hospital of Catanzaro 10 fulfilled the study's inclusion criteria: 5 were assigned to G1a and 5 to G1b, with a total of 30 volumetric measurements. In G2, we included 10 patients, with a total of 20 volumetric measurements. From the volumetric measurements and statistical analysis carried out, it emerged that the average of the volumetric differences of the healthy orbits was ±0.635,1 cm3, the standard deviation of the volumetric differences was ±0.338,3, and the relationship between the treated orbit and the healthy orbit was linear; therefore, the treated orbital volumes tend to approach the healthy ones after surgical treatment. Conclusion: This study demonstrates that if the volume is restored within the range of the standardized mean, the diplopia is completely recovered already after surgery or after one month. For orbital volumes that do not fall within this range, functional recovery could occur within 6 months or be lacking. The restoration of the orbital volume using pre-modeled networks on the patient's anatomical model, printed internally in 3D, allows for more accurate reconstructions of the orbital floor in less time, with clinical advantages also in terms of surgical timing.

Individual Design and Rapid Prototyping in Reconstruction of Orbital Wall Defects.

Application of Three-Dimensional Printing Technology in the Orbital Blowout Fracture Reconstruction.

Reconstruction of orbital floor fractures: comparison of individual prefabricated titanium implants and calvarial bone grafts.

Late reconstruction of the complex orbital fractures with computer-aided design and computer-aided manufacturing technique

Exploring 3D Printed Implants With Anti-Dropout Function to Overcome Time Constraints in Acute Orbital Fractures for Patient-Specific Implants

[Reconstruction of the Orbital Fracture with Enophthalmos Using Customized Titanium Mesh Combined with Medpor].

Evaluation of Computer-Based Volume Measurement and Porous Polyethylene Channel Implants in Reconstruction of Large Orbital Wall Fractures.

[Computer-Assisted Fabricated Individual Titanium Mesh for Reconstruction of Orbital Wall].

Orbital Floor Reconstruction: a Retrospective Study of 21 Cases

Classical Orbital Floor Post-Traumatic Reconstruction vs. Customized Reconstruction with the Support of "In-House" 3D-Printed Models: A Retrospective Study with an Analysis of Volumetric Measurement

Evaluation of the Application of Computer-Aided Shape-Adapted Fabricated Titanium Mesh for Mirroring-Reconstructing Orbital Walls in Cases of Late Post-Traumatic Enophthalmos.

Clinical effects of 3-D printing-assisted personalized reconstructive surgery for blowout orbital fractures

[Individual 3-D image prototyping models for orbital reconstruction].

Application of Navigation and Individual Designed Titanium Mesh in the Treatment of Delayed Orbitozygomatic Fractures with Enophthalmos

Presurgical Virtual Planning and Intraoperative Navigation with 3D-Preformed Mesh: A New Protocol for Primary Orbital Fracture Reconstruction

Delayed Orbital Floor Reconstruction Using Mirroring Technique and Patient-Specific Implants: Proof of Concept

Patient-Specific Implant Customization for Treatment of Internal Orbital Fractures Using Office-Based Three-Dimensional Printing

[Application of Preformed Orbital Titanium Mesh in Reconstruction of Orbital Fracture].

Digital Design And Individually Fabricated Titanium Implants For The Reconstruction Of Traumatic Zygomatico-Orbital Defects

Automatic Design and Fabrication of a Custom Ocular Prosthesis Using 3D Volume Difference Reconstruction (VDR)

Immediate reconstruction of bilateral mandible defects: management based on computer-aided design/computer-aided manufacturing rapid prototyping technology in combination with vascularized fibular osteomyocutaneous flap.