Abstract:Background: Orbital floor fractures (OFFs) represent an interesting chapter in maxillofacial surgery, and one of the main challenges in orbit reconstruction is shaping and cutting the precise contour of the implants due to its complex anatomy. Objective: The aim of the retrospective study was to demonstrate, through pre- and postoperative volumetric measurements of the orbit, how the use of a preformed titanium mesh based on the stereolithographic model produced with 3D printers ("In-House" reconstruction) provides a better reconstruction volumetric compared to the intraoperatively shaped titanium mesh. Materials and Methods: The patients with OFF enrolled in this study were divided into two groups according to the inclusion criteria. In Group 1 (G1), patients surgically treated for OFF were divided into two subgroups: G1a, patients undergoing orbital floor reconstruction with an intraoperatively shaped mesh, and G1b, patients undergoing orbital floor reconstruction with a preoperative mesh shaped on a 3D-printed stereolithographic model. Group 2 (G2) consisted of patients treated for other traumatic pathologies (mandible fractures and middle face fractures not involving orbit). Pre- and postoperative orbital volumetric measurements were performed on both G1 and G2. The patients of both groups were subjected to the measurement of orbital volume using Osirix software (Pixmeo SARL, CH-1233 Bernex, Switzerland) on the new CT examination. Both descriptive (using central tendency indices such as mean and range) and regressive (using the Bravais–Pearson index, calculated using the GraphPad program) statistical analyses were performed on the recorded data. Results: From 1 January 2017 to 31 December 2021, of the 176 patients treated for OFF at the "Magna Graecia" University Hospital of Catanzaro 10 fulfilled the study's inclusion criteria: 5 were assigned to G1a and 5 to G1b, with a total of 30 volumetric measurements. In G2, we included 10 patients, with a total of 20 volumetric measurements. From the volumetric measurements and statistical analysis carried out, it emerged that the average of the volumetric differences of the healthy orbits was ±0.635,1 cm3, the standard deviation of the volumetric differences was ±0.338,3, and the relationship between the treated orbit and the healthy orbit was linear; therefore, the treated orbital volumes tend to approach the healthy ones after surgical treatment. Conclusion: This study demonstrates that if the volume is restored within the range of the standardized mean, the diplopia is completely recovered already after surgery or after one month. For orbital volumes that do not fall within this range, functional recovery could occur within 6 months or be lacking. The restoration of the orbital volume using pre-modeled networks on the patient's anatomical model, printed internally in 3D, allows for more accurate reconstructions of the orbital floor in less time, with clinical advantages also in terms of surgical timing.

Reconstruction of orbital floor fractures: comparison of individual prefabricated titanium implants and calvarial bone grafts.

Application of Three-Dimensional Printing Technology in the Orbital Blowout Fracture Reconstruction.

Individual Design and Rapid Prototyping in Reconstruction of Orbital Wall Defects.

Orbital Floor Reconstruction: a Retrospective Study of 21 Cases

Comparison of Postoperative Enophthalmos Between Fresh and Delayed Unilateral Orbital Fractures After Orbital Reconstruction With Titanium Mesh Using Computer-Assisted Navigation.

Customized orbital implant versus 3D preformed titanium mesh for orbital fracture repair: A retrospective comparative analysis of orbital reconstruction accuracy

[Application of Preformed Orbital Titanium Mesh in Reconstruction of Orbital Fracture].

The effect of titanium mesh implantation for the treatment of enophthalmos secondary to inferior orbital wall fracture

[Three-Dimensionally Preformed Titanium Mesh Plates for Posttraumatic Complex Orbital Bone Fracture Reconstruction].

Evaluation of Computer-Based Volume Measurement and Porous Polyethylene Channel Implants in Reconstruction of Large Orbital Wall Fractures.

[Computer-Assisted Fabricated Individual Titanium Mesh for Reconstruction of Orbital Wall].

Comparison of post-operative outcomes of graft materials used in reconstruction of blow-out fractures

Assessing the Adequacy of Orbital Reconstruction With Titanium Mesh Using Clinical and Radiological Measures

[Reconstruction of the Orbital Fracture with Enophthalmos Using Customized Titanium Mesh Combined with Medpor].

Titanium mesh implantation for the treatment of enophthalmos caused by blow-out fractures of orbital medial and inferior walls

Classical Orbital Floor Post-Traumatic Reconstruction vs. Customized Reconstruction with the Support of "In-House" 3D-Printed Models: A Retrospective Study with an Analysis of Volumetric Measurement

Exploring 3D Printed Implants With Anti-Dropout Function to Overcome Time Constraints in Acute Orbital Fractures for Patient-Specific Implants

Prebending of Prefabricated Orbital Implants: Towards Improved Orbital Angle Symmetry Post Craniofacial Trauma Surgery

Delayed Orbital Floor Reconstruction Using Mirroring Technique and Patient-Specific Implants: Proof of Concept

Clinical and radiographic assessment of patient-specific transantral reconstruction of orbital floor fractures: A case series

Evaluation of the Application of Computer-Aided Shape-Adapted Fabricated Titanium Mesh for Mirroring-Reconstructing Orbital Walls in Cases of Late Post-Traumatic Enophthalmos.