Abstract:Background: Orbital floor fractures (OFFs) represent an interesting chapter in maxillofacial surgery, and one of the main challenges in orbit reconstruction is shaping and cutting the precise contour of the implants due to its complex anatomy. Objective: The aim of the retrospective study was to demonstrate, through pre- and postoperative volumetric measurements of the orbit, how the use of a preformed titanium mesh based on the stereolithographic model produced with 3D printers ("In-House" reconstruction) provides a better reconstruction volumetric compared to the intraoperatively shaped titanium mesh. Materials and Methods: The patients with OFF enrolled in this study were divided into two groups according to the inclusion criteria. In Group 1 (G1), patients surgically treated for OFF were divided into two subgroups: G1a, patients undergoing orbital floor reconstruction with an intraoperatively shaped mesh, and G1b, patients undergoing orbital floor reconstruction with a preoperative mesh shaped on a 3D-printed stereolithographic model. Group 2 (G2) consisted of patients treated for other traumatic pathologies (mandible fractures and middle face fractures not involving orbit). Pre- and postoperative orbital volumetric measurements were performed on both G1 and G2. The patients of both groups were subjected to the measurement of orbital volume using Osirix software (Pixmeo SARL, CH-1233 Bernex, Switzerland) on the new CT examination. Both descriptive (using central tendency indices such as mean and range) and regressive (using the Bravais–Pearson index, calculated using the GraphPad program) statistical analyses were performed on the recorded data. Results: From 1 January 2017 to 31 December 2021, of the 176 patients treated for OFF at the "Magna Graecia" University Hospital of Catanzaro 10 fulfilled the study's inclusion criteria: 5 were assigned to G1a and 5 to G1b, with a total of 30 volumetric measurements. In G2, we included 10 patients, with a total of 20 volumetric measurements. From the volumetric measurements and statistical analysis carried out, it emerged that the average of the volumetric differences of the healthy orbits was ±0.635,1 cm3, the standard deviation of the volumetric differences was ±0.338,3, and the relationship between the treated orbit and the healthy orbit was linear; therefore, the treated orbital volumes tend to approach the healthy ones after surgical treatment. Conclusion: This study demonstrates that if the volume is restored within the range of the standardized mean, the diplopia is completely recovered already after surgery or after one month. For orbital volumes that do not fall within this range, functional recovery could occur within 6 months or be lacking. The restoration of the orbital volume using pre-modeled networks on the patient's anatomical model, printed internally in 3D, allows for more accurate reconstructions of the orbital floor in less time, with clinical advantages also in terms of surgical timing.

Exploring 3D Printed Implants With Anti-Dropout Function to Overcome Time Constraints in Acute Orbital Fractures for Patient-Specific Implants

Application of Three-Dimensional Printing Technology in the Orbital Blowout Fracture Reconstruction.

Patient-Specific Implant Customization for Treatment of Internal Orbital Fractures Using Office-Based Three-Dimensional Printing

Clinical effects of 3-D printing-assisted personalized reconstructive surgery for blowout orbital fractures

Use of 3D-printed model to plan the surgical management of a patient with isolated orbital floor fracture: a case report

Engineering Self-Antimicrobial Implants with Precision Pore Architectures for Personized Orbital Reconstruction

Individual Design and Rapid Prototyping in Reconstruction of Orbital Wall Defects.

Does a Point-of-Care 3-Dimensional Printer Result in a Decreased Length of Surgery for Orbital Fractures?

Classical Orbital Floor Post-Traumatic Reconstruction vs. Customized Reconstruction with the Support of "In-House" 3D-Printed Models: A Retrospective Study with an Analysis of Volumetric Measurement

Orbital floor reconstruction based on 3d printed model - case report

Observation on the efficacy of application of 3D printing technique in repair surgery for the orbital blowout fracture

Next-generation Finely Controlled Graded Porous Antibacterial Bioceramics for High-Efficiency Vascularization in Orbital Reconstruction

Long-Term Enophthalmos After Complex Orbital Bone Loss Successfully Treated with Patient-Specific Porous Titanium Implants: A Case Series

Virtual Planning and 3D Printing in the Management of Acute Orbital Fractures and Post-Traumatic Deformities

Customized orbital implant versus 3D preformed titanium mesh for orbital fracture repair: A retrospective comparative analysis of orbital reconstruction accuracy

Evaluation of Computer-Based Volume Measurement and Porous Polyethylene Channel Implants in Reconstruction of Large Orbital Wall Fractures.

Reconstruction of orbital floor fractures: comparison of individual prefabricated titanium implants and calvarial bone grafts.

Late reconstruction of the complex orbital fractures with computer-aided design and computer-aided manufacturing technique

Delayed Orbital Floor Reconstruction Using Mirroring Technique and Patient-Specific Implants: Proof of Concept

Reconstruction of Orbital Wall Fractures with a Combination of Resorbable Plates and Antibiotic-Impregnated Collagen Sheets

Comparison of patient specific implant reconstruction vs conventional titanium mesh reconstruction of orbital fractures using a novel method