Abstract:Numerous combustion strategies have been suggested for compression ignition engines in order to meet the stringent emission regulations with minimal sacrifice in the fuel economy. Premixed charge compression ignition combustion has the potential to reduce the nitrogen oxide emissions and the soot emissions while maintaining a high thermal efficiency and has become the research focus recently. Experiments and simulations were used to study the effects of the injection mode and the injection timing on the premixed charge compression ignition combustion and the emissions in a heavy-duty diesel engine at low and medium loads. The results reveal the following. At low loads, when the injection timing of a single injection is 35° crank angle before top dead centre because of the impinging position of the spray, the mixture is divided into two parts: the fuel above the chamber and the fuel in the piston bowl. This helps to utilize fully the in-cylinder air to form a homogeneous mixture. Also the nitrogen oxide emissions are the lowest. At medium loads, with a single injection, the injection mass is increased, the injection duration is prolonged and the mixing timing is reduced. As a result, the soot emissions, the carbon monoxide emissions and the unburned hydrocarbon emissions are increased dramatically; the best emissions are gained at an injection timing of 35° crank angle before top dead centre owing to the combined effect of the optimized mixing time and the optimized mixing space. At medium loads, with multiple injections, the injection mass is divided into four pulses, the mixing timings of which are all increased. The mixing space of the fuel–air mixture is also improved, and a more homogeneous mixture is obtained, which is beneficial to decreasing the soot emissions, the carbon monoxide emissions and the unburned hydrocarbon emissions in comparison with those for the single-injection case. When the injection timings of multiple injections are 80° crank angle before top dead centre, 65° crank angle before top dead centre, 50° crank angle before top dead centre and 35° crank angle before top dead centre, the best trade-off between the performance and the emissions can be achieved at medium loads.

Combustion Characteristics and Emission of a Two-Stroke Compression Ignition Engine with Two-Stage Injection

Improvement of Emission Performance of Two-stroke Diesel Engines with Two-stage Injection

Numerical Investigation of the Effect of Two-Stage Injection Strategy on Combustion and Emission Characteristics of a Diesel Engine

Simulation on two-stage injection combustion of diesel engine under light load

Effect of Two-Stage Injection on Unburned Hydrocarbon and Carbon Monoxide Emissions in Smokeless Low-Temperature Diesel Combustion with Ultra-High Exhaust Gas Recirculation

Influence of Multi-Injection on Combustion and Emission of Diesel Engine

Effects of Injection Timing and Injection Volume on the Combustion and Emissions of a Two-Stroke Kerosene Direct Injection Engine

Study on the combustion and emission characteristics of a diesel engine with multi-injection modes based on experimental investigation and computational fluid dynamics modelling

Experimental study of independent two-stage in-cylinder heat release using jet controlled compression ignition

Effects of the Injection Parameters on the Premixed Charge Compression Ignition Combustion and the Emissions in A Heavy-Duty Diesel Engine

Analysis of Influences of Injection Parameters on Combustion Process Based on 2-Stroke Rod-Less Opposed Piston Diesel Engine

Investigations of split injection strategies for the improvement of combustion and soot emissions characteristics based on the two-color method in a heavy-duty diesel engine

Exploring the Combustion Performance of a Non-Road Air-Cooled Two-Cylinder Turbocharged Diesel Engine

Control of Ignition Timing and Combustion Phase by Means of Injection Strategy for Jet-Controlled Compression Ignition Mode in a Light Duty Diesel Engine

Effects of Injection Timing and Compression Ratio on the Combustion Performance and Emissions of a Two-Stroke DISI Engine Fuelled with Aviation Kerosene

Study of Pilot Injection for the Improvement of Combustion and Emissions Characteristics in A Heavy-Duty Diesel Engine

Nonuniform Mixture Formation by a Two-Stage Gasoline Direct Injection Combustion System

Effect of Two-Stage Injections on Unburned Hydrocarbon and Carbon Monoxide Emissions from Ultra-High EGR Low Temperature Diesel Combustion(Thermal Engineering)

Experimental investigation on emissions and combustion characteristics of two-stage turbocharged heavy-duty diesel engine

Study of Two-Stage Injection in Optimizing Cold-Start Emission Characteristics of GDI Engine

Experimental study of the pilot injection strategy effects on diesel engine combustion and its emission