Abstract:Numerous combustion strategies have been suggested for compression ignition engines in order to meet the stringent emission regulations with minimal sacrifice in the fuel economy. Premixed charge compression ignition combustion has the potential to reduce the nitrogen oxide emissions and the soot emissions while maintaining a high thermal efficiency and has become the research focus recently. Experiments and simulations were used to study the effects of the injection mode and the injection timing on the premixed charge compression ignition combustion and the emissions in a heavy-duty diesel engine at low and medium loads. The results reveal the following. At low loads, when the injection timing of a single injection is 35° crank angle before top dead centre because of the impinging position of the spray, the mixture is divided into two parts: the fuel above the chamber and the fuel in the piston bowl. This helps to utilize fully the in-cylinder air to form a homogeneous mixture. Also the nitrogen oxide emissions are the lowest. At medium loads, with a single injection, the injection mass is increased, the injection duration is prolonged and the mixing timing is reduced. As a result, the soot emissions, the carbon monoxide emissions and the unburned hydrocarbon emissions are increased dramatically; the best emissions are gained at an injection timing of 35° crank angle before top dead centre owing to the combined effect of the optimized mixing time and the optimized mixing space. At medium loads, with multiple injections, the injection mass is divided into four pulses, the mixing timings of which are all increased. The mixing space of the fuel–air mixture is also improved, and a more homogeneous mixture is obtained, which is beneficial to decreasing the soot emissions, the carbon monoxide emissions and the unburned hydrocarbon emissions in comparison with those for the single-injection case. When the injection timings of multiple injections are 80° crank angle before top dead centre, 65° crank angle before top dead centre, 50° crank angle before top dead centre and 35° crank angle before top dead centre, the best trade-off between the performance and the emissions can be achieved at medium loads.

Experimental study of independent two-stage in-cylinder heat release using jet controlled compression ignition

Control of Ignition Timing and Combustion Phase by Means of Injection Strategy for Jet-Controlled Compression Ignition Mode in a Light Duty Diesel Engine

Twin-Peak Heat Release Phenomenon Inside a Heavy-Duty Diesel Engine Retrofitted to Natural-Gas Spark Ignition

Multiple-objective optimization of Jet Controlled Compression Ignition (JCCI) mode with dual-direct injection in a high-speed light-duty engine

Experimental and Numerical Study of Jet Controlled Compression Ignition on Combustion Phasing Control in Diesel Premixed Compression Ignition Systems

Investigation of the Combustion and Emission Characteristics of Partially Premixed Compression Ignition in A Heavy-Duty Diesel Engine

Investigations of split injection strategies for the improvement of combustion and soot emissions characteristics based on the two-color method in a heavy-duty diesel engine

Experimental Study on the Diesel Injection Pressure of Homogeneous Charge Induced Ignition for Multi-cylinder Operation

Exploring the Effects of the Key Multi-Injection Parameters on Combustion and Emissions in Intelligent Charge Compression Ignition (ICCI) Mode

Towards High Efficiency of Intelligent Charge Compression Ignition (ICCI) Engine by Optimizing the High-Reactivity Fuel Injection Strategies under Medium–high Loads

Investigation of Two-Stage Split-Injection Strategies for a Dieseline Fuelled PPCI Engine

Study of pulse spray, heat release, emissions and efficiencies in a compound diesel HCCI combustion engine

Experimental Research on Controllability and Emissions of Jet-Controlled Compression Ignition Engine

Effects of the Injection Parameters on the Premixed Charge Compression Ignition Combustion and the Emissions in A Heavy-Duty Diesel Engine

Experimental Studies on the Key Parameters Controlling the Combustion and Emission in Premixed Charge Compression Ignition Concept Based on Diesel Surrogates

Parametric Study on the Methanol/diesel JCCI Mode with Dual-Direct Injection System in a Light-Duty Engine

The Potential of High-load Extension by Using Late Intake Valve Closing for a Diesel Premixed Charge Compression Ignition (PCCI) Engine

Study on the combustion and emission characteristics of a diesel engine with multi-injection modes based on experimental investigation and computational fluid dynamics modelling

Characterizing the Role of Fuel Injection Strategies on Performance, Combustion, and Emissions in Intelligent Charge Compression Ignition (ICCI) Mode

An Experimental Study of Hcci-Di Combustion and Emissions in A Diesel Engine with Dual Fuel

An Experimental Investigation of Optimizing Control of Compound Charge Compression Ignition(CCCI)Combustion in an Engine Fueled with DME