Abstract:Reversible pump turbine (RPT) is designed for pumping water from a lower reservoir to a higher reservoir by using the surplus energy in the power grids. Furthermore, this water have to go down to generate electrical energy by RPT at peak hours or in case of emergency. RPT have to change the working condition between pump mode and turbine mode [1]. In order to meet the requirement of power grid, RPT usually works at low load off-design working condition. Due to RPT’s special way of operating, it’s hard to guarantee the stability of the units. Few years ago, both in TianHuangping pump storage power station [2] and YiXing pump storage power station [3], the abnormal sound and vibration occurs at the distributor of the RPT which in the pump mode when the guide vane opening is very small. In order to resolve this problem, B Nennemann [4] has conducted a detailed research about the abnormal phenomena which happened in YiXing pump storage power station by using 2-D periodical CFD simulation. Eventually, the author acclaimed that the unexpected bi-stable flow conditions and a self-excited torsion mode flutter vibration of the guide vane caused this problem, moreover, the vibration problem can be eliminated by modifying the shape of the guide vane successfully. Addressing the issue of TianHuangping, H G Fan [5] studied the HT of the guide vane of the RPT during the startup process and shutdown process in turbine mode by 2-D periodical CFD simulation. His work indicated that repeating reversal of fluid occurs when the guide vane at slight opening during the shutdown process in turbine mode. This phenomena finally results in the dramatically increasing of the HT which makes the vibration happens. Our previous work [6] has performed the 3-D CFD simulation of the startup process of the pump turbine of Tian Huangping pump storage power station which in the pump mode by implementing the dynamic meshing technique. The results indicates that the main flow between the guide vanes has experienced a deflection when the guide vane opening is very small, and this deflection leads to the sharply changing of the hydraulic torque on the guide vanes, if the transmission of the distributer cannot adapt this changing immediately, the vibration and abnormal sound will occur in the unit. Based on the previous flow field analysis [6] of the dynamic process. This paper presents a structural characteristic analysis of the guide vanes when the pump turbine works in pump mode at slight opening region. The one-way FSI method was carried out to calculate the structural characteristic of guide vanes during the main flow deflection process. And the vibration characteristic of the guide vanes were analyzed. The result shows that the position of the guide vane has a significant influence on the stress and strain of guide vanes.

DYNAMIC ANALYSIS OF A HYDRAULIC TURBINE UNIT*

A Simulation Study of Hydraulic Vibration caused by Clearance Flow in a Pump Turbine

Dynamic characteristics of the rotor system for large pump-turbine sets

Numerical Research on Dynamic Lateral Vibration of a Pump Turbine’s Shaft System

Influence Of Bearing Pre-Load Coefficient On Shaft Vibration And Pad Temperature In A Hydroturbine Generator Unit - A Case Study

Rotor-dynamic Characteristics Analysis of a Large-Scale Francis Turbine Shaft-System

Influence Of Typical Assembling Condition Of Bearings On Shaft Lateral Vibration In A Hydraulic Generator Unit

Numerical Analysis on the Hydraulic Thrust and Dynamic Response Characteristics of a Turbine Pump

Loading Methodology and Dynamics Analysis of the Digital-Servo Hydraulic Cylinders Group in Large Wind Turbine Drivetrain Test Bench

MODEL ANALYSIS AND TEST RESEARCH OF HORIZONTAL-AXIAL MARINE CURRENT TURBINE

Calculation and Analysis of Dynamic Load of the Rotor-bearing System in Hydro Unit Based on the Axis Orbit

Effect of Unbalanced Magnetic Pull of Generator Rotor on the Dynamic Characteristics of a Pump—Turbine Rotor System

Nonlinear Hydraulic Vibration Modeling and Dynamic Analysis of Hydro-Turbine Generator Unit with Multiple Faults

Analysis on Modeling Rotor System with Sidling Bearing and Ring Seal by Using FEM

Dynamic Analyses of the Hydro-Turbine Generator Shafting System Considering the Hydraulic Instability

Structural characteristic analysis of the guide vanes of a pump turbine which working at the slight opening region

Numerical Study on the Flow and Structural Characteristics of a Large High Head Prototype Pump-Turbine under Different Operating Conditions

Analysis of the Influence of the Mechanical Imbalance and the Bearing Clearance on the Operating Stability of Hydro-power Unit

The characteristic analysis of rotor dynamics of large hydraulic generating uint

Analysis of Shafting System Vibration Characteristics for Mixed-Flow Hydropower Units Considering Sand Wear on Turbine Blades

Analysis of Flow and Runner Dynamic Response Characteristics under Pump Conditions of Variable-Speed Pump Turbine