Abstract:An in-situ compatibilized starch (St) and polyacrylonitrile (PAN) composite spinning solution was designed by preparing starch-graft-polyacrylonitrile (St-g-PAN) through graft copolymerizing acrylonitrile from soluble starch and using ammonium cerium nitrate (CAN) as initiator. As dimethyl sulfoxide (DMSO) was used as the solvent, St/St-g-PAN/PAN/DMSO spinning solution was prepared and St/St-g-PAN/PAN composite fibers were obtained by dry-wet spinning technique. The effects of air gap, coagulation bath, hot drawing and stretching, and thermal-setting process were studied in detail. Fourier transform infrared spectroscopy (FT-IR), solid state nuclear magnetic resonance (13C NMR), thermogravimetric analysis (TGA), X-ray diffraction analysis (XRD), and scanning electron microscopy (SEM) were used to characterize the structure and morphology of the copolymer and the fibers. Single fiber strength tester and sonic orientation instrument were performed to measure the fiber mechanical properties and orientation degrees. The results showed that as the grafting ratio ~150.0% and the reacting mixture containing St ~9.8%, St-g-PAN ~81.6%, and homo-PAN ~8.6% in DMSO solution with 6.0 wt% in concentration were used, the spinning parameters such as air gap ~35 mm, coagulation bath concentration ~70%, temperature ~25 °C, and positive stretching ~48%, hot drawing and stretching 6 times at 80 °C, thermal-setting at 90 °C for 3 h under constant length mode were met, composite fibers with breaking strength 3.41 cN·dtex−1, breaking elongation 14.41%, sonic orientation factor 0.625, moisture recovery ratio 10.53% under standard condition (1 atm, 22 °C, and relative humidity 65%), and boiling water shrinkage ratio 9.60% were obtained. The as prepared composite fiber was better than common viscose fiber 2.11 cN·dtex−1 and cotton fiber ~3.24 cN·dtex−1 and expected to be used in the fields of medical gauze, bandage, protective clothing, et al. besides of common textiles. The in-situ compatibilization method can be applied in preparation of other composite polymer materials.

Stretching-Induced Crystallinity and Orientation to Improve the Mechanical Properties of Electrospun Pan Nanocomposites

Carbon-nanotube-templated Carbon Nanofibers with Improved Mechanical Performance

Significant Improvement of Mechanical Properties Observed in Highly Aligned Carbon-Nanotube-Reinforced Nanofibers

Strengthening Carbon Nanotube Fibers with Semi-Crystallized Polyvinyl Alcohol and Hot-Stretching

Enhanced Mechanical Performance of Electrospun Graphene/Polyacrylonitrile (PAN) Composite Microfibrous Yarns Via Post-Processing

Graphene-embedded electrospun polyacrylonitrile nanofibers with enhanced thermo-mechanical properties

Plastic deformation of the microfibrils in wet polyacrylonitrile fibers induced by the stretching field

Enhancing Carbon Nanotube Yarns via Infiltration Filling with Polyacrylonitrile in Supercritical Carbon Dioxide

Chain conformation, crystallization behavior, electrical and mechanical properties of electrospun polymer-carbon nanotube hybrid nanofibers with different orientations

New Insights into Orientation Differences Between Skin and Core Regions of Polyacrylonitrile Fibers During Pre-Stabilization with the Stretching Process

Improved Mechanical and Electrical Properties in Electrospun Polyimide/multiwalled Carbon Nanotubes Nanofibrous Composites

Stretch-Modulated Carbon Nanotube Alignment In Ferroelectric Polymer Composites: Characterization Of The Orientation State And Its Influence On The Dielectric Properties

High-Strength and Conductive Electrospun Nanofiber Yarns

Polyacrylonitrile/multi-walled carbon nanotubes/polyurethane electrospun nanofiber membranes for sports equipment

In-situ compatibilized starch/polyacylonitrile composite fiber fabricated via dry-wet spinning technique

Microstructural Evolution during Dry-Jet Wet Spinning Postprocessing from Coagulation Bath Fiber to High-Performance Polyacrylonitrile Precursor Fiber

Enhancing mechanical strength of electrospun nanofibers by coaxial electrospinning and thermal treatment

Flexible Conductive Fibers from Alginate, Cellulose Nanocrystals, and Polyaniline by Wet Spinning

Treatment of recurrent condyloma acuminatum.

Molecular Dynamics Simulations of Stretch-Induced Crystal Changes in Crystallized Polyethylene/Carbon Nanotubes Nanocomposites

Structure and Morphological Evolvement of Electrospun Polyacrylonitrile/Organic–Modified Fe-Montmorillonite Composite Carbon Nanofibers