Abstract:AlH3 is a metastable hydride with a high hydrogen density of 10.1 wt% and it can release hydrogen at a low temperature of 150-200 degrees C. Many additives (e.g., NbF5, TiF3, etc.) intro-duced by ball milling can significantly reduce the decomposition temperature of AlH3, but often simultaneously decrease the available hydrogen capacity. In this work, TiB2 was introduced by ball milling to improve the decomposition performance of AlH3. AlH3 + x wt% TiB2 (x = 2.5, 5, 7.5, 10) composites were prepared by ball milling, and the milling conditions were optimized. It was shown that the decomposition performance of the AlH3 + 2.5 wt% TiB2 ball milled at 225 rpm for 108 min is the best. The onset decomposition temperature is 78 degrees C, which is 60 degrees C lower than that of pure AlH3. The decomposition is terminated at 130 degrees C with 8.5 wt% of hydrogen is obtained. In addition, 5.3 wt% of hydrogen can be released within 200 min at constantly 80 degrees C. Under the same conditions, ball-milled AlH3 can hardly release any hydrogen. The activation energy calculated by the Kissinger's method is 86 kJ mol-1, which was 28 kJ mol-1 lower than that of ball-milled AlH3. Catalytic mechanism study reveals that the Al2O3 layers on the surface of AlH3 will interact with TiB2 to form Al-Ti-B solid solution, resulting in lattice distortion. Through lattice activation, the decom-position kinetics of AlH3 is improved. This work provides an efficient strategy to achieve both high hydrogen capacity and low decomposition temperature of metastable AlH3 by proper ball milling with metal borides.(c) 2022 Hydrogen Energy Publications LLC. Published by Elsevier Ltd. All rights reserved.

Hydrolysis of ball milling Al–Bi–hydride and Al–Bi–salt mixture for hydrogen generation

Investigation on the Improved Hydrolysis of Aluminum–calcium Hydride-Salt Mixture Elaborated by Ball Milling

Effect of Salts Addition on the Hydrogen Generation of Al–LiH Composite Elaborated by Ball Milling

Hydrogen generation from the hydrolysis of Mg powder ball-milled with AlCl3

Improved Hydrogen Generation from the Hydrolysis of Aluminum Ball Milled with Hydride

Study on Hydrogen Generation from the Hydrolysis of a Ball Milled Aluminum/calcium Hydride Composite

Enhanced Hydrogen Generation Performance of Al-Rich Alloys by a Melting-Mechanical Crushing-Ball Milling Method

Improved Hydrogen Storage Properties of MgH2 by Ball Milling with AlH3: Preparations, De/rehydriding Properties, and Reaction Mechanisms

Dehydriding properties of γ-AlH3

In situ hydrogen production from Al–BiCl 3 hydrolysis for small-sized fuel cell

Synergistic Effect of LiBH4and LiAlH4Additives on Improved Hydrogen Storage Properties of Unexpected High Capacity Magnesium Hydride

Hydrogen Generation from the Reaction of Al-based Composites Activated by Low-Melting-point Metals/oxides/salts with Water

A high activity Al–Bi@C for hydrogen generation from Al-water reaction

Hydrogen Generation from Mg–LiBH4 Hydrolysis Improved by AlCl3 Addition

Achieving Both High Hydrogen Capacity and Low Decomposition Temperature of the Metastable AlH3 by Proper Ball Milling with TiB2

Mild hydrogen production from the hydrolysis of Al–Bi–Zn composite powder

Preparation of Al-3Ga-3In-3Sn Alloy Powder by Coupling Alloying and Ball Milling and Its Application on High-Rate Hydrogen Generation at Room Temperature

Controllable Hydrolysis Performance Of Mgli Alloys And Their Hydrides

Exploration of hydrogen generation from an Mg-LiBH4 system improved by NiCl2 addition

Promoting Al hydrolysis via MgH2 and NaOH addition

Directed Stabilization by Air-Milling and Catalyzed Decomposition by Layered Titanium Carbide Toward Low-Temperature and High-Capacity Hydrogen Storage of Aluminum Hydride