Abstract:Organometallically prepared AlH3 and as-received Al powders were mixed with MgH2 to improve the dehydriding and rehydriding properties of MgH2. Thermal analysis shows that the onset dehydriding temperature of MgH2 is reduced by 55 degrees C (or 25 degrees C) when mixed with AlH3 (or Al). The destabilization of MgH2 is attributed to the formation of Mg-Al alloys through the reaction between MgH2 and Al. Isothermal dehydriding measurements demonstrate that AlH3 and Al both improve the dehydriding kinetic of MgH2 to some extent, and it only takes 44 min for MgH2 + AlH3 (5.4 h for MgH2 + Al) to release 60% of the hydrogen of MgH2 at 300 degrees C, but 8.6 h are required for as-milled MgH2. The apparent activation energy for the dehydriding of MgH2 is reduced from 174.6 kJ mol(-1) for as-milled MgH2 to 154.8 and 138.1 kJ mol(-1) for MgH2 mixed with Al and AlH3 respectively; this is responsible for the improvement in the dehydriding kinetics of MgH2. Despite this, AlH3 is better in destabilizing MgH2 than the as-received Al for the fact that Al* formed in situ from the decomposition of AlH3 is oxide-free on the particle surfaces, which effectively increases the chemical activity of Al*. Furthermore, the brittleness of AlH3 makes it easier to mix MgH2 with AlH3, which would result in uniform distributions of Mg and Al and shortening of the diffusion length. Concerning the reversibility, at 300 degrees C and 5 MPa H-2 and MgH2 are fully recovered in the dehydrided MgH2 + Al, and MgH2 + AlH3 samples after rehydriding for 10 h. The rehydriding kinetic of MgH2 is significantly enhanced for the dehydrided MgH2 + AlH3, but not in the case of the MgH2 + Al.

Enhanced Hydrogen Generation Performance of Al-Rich Alloys by a Melting-Mechanical Crushing-Ball Milling Method

Improved Hydrogen Generation from the Hydrolysis of Aluminum Ball Milled with Hydride

Study on Hydrogen Generation from the Hydrolysis of a Ball Milled Aluminum/calcium Hydride Composite

Effect of Salts Addition on the Hydrogen Generation of Al–LiH Composite Elaborated by Ball Milling

Investigation on the Improved Hydrolysis of Aluminum–calcium Hydride-Salt Mixture Elaborated by Ball Milling

Preparation of Al-3Ga-3In-3Sn Alloy Powder by Coupling Alloying and Ball Milling and Its Application on High-Rate Hydrogen Generation at Room Temperature

Hydrogen generation from the hydrolysis of Mg powder ball-milled with AlCl3

Hydrogen Generation from the Reaction of Al-based Composites Activated by Low-Melting-point Metals/oxides/salts with Water

Effects of Preparation Method on the Hydrolytic Hydrogen Production Performance of Al-rich Alloys

Hydrolysis-Based Hydrogen Generation Investigation of Aluminum System Adding Low-Melting Metals

Experimental Study on the Effect of Low Melting Point Metal Additives on Hydrogen Production in the Aluminum–water Reaction

Hydrolysis of ball milling Al–Bi–hydride and Al–Bi–salt mixture for hydrogen generation

Molten Salt-Enhanced Production of Hydrogen by Using Skimmed Hot Dross from Aluminum Remelting at High Temperature

Enhanced Hydrogen Generation from Magnesium-Aluminum Scrap Ball Milled with Low Melting Point Solder Alloy

Exploration of hydrogen generation from an Mg-LiBH4 system improved by NiCl2 addition

Dehydriding properties of γ-AlH3

The effects of mechanical grinding on the hydrogen storage properties of MlNi4.7Al0.3 alloy

Hydrogen Generation from Mg–LiBH4 Hydrolysis Improved by AlCl3 Addition

Improved Hydrogen Storage Properties of MgH2 by Ball Milling with AlH3: Preparations, De/rehydriding Properties, and Reaction Mechanisms

Effect of ball-milling on the phase structure and hydrogen storage properties of Ti0.9Zr0.1Mn1.5 alloy

Hydrogen Generation from Mg Wastes by Cold Rolling and Ball Milling by Hydrolysis Reaction: Elektron 21 (UNS-M12310) in Simulated Seawater