Abstract:Thermal shrinkage has for long been a critical issue in nonwoven industrial applications. A dimensionally stable nonwoven web with excellent mechanical property was achieved by heat treatment with tension [taut annealed (TA)] instead of annealing under free state [free annealed (FA)], while the original high porosity was not affected. To better understand the fundamental structure-property relationship, these two different heat treatments' effects on the thermal behaviors, morphology, and phase structures of poly(phenylene sulfide) (PPS) nonwovens were elucidated via a combination of different experimental techniques such as temperature-modulated differential scanning calorimetry (DSC), two-dimensional wide-angle X-ray diffraction, two-dimensional small-angle X-ray scattering, and polarized Raman spectroscopy. It is evidenced that no obvious online stress-induced crystallization occurs during the melt-blowing process, making virgin PPS fibers mostly in the amorphous state. However, experimental results confirm that a certain amount of mesophase or constrained amorphous exists in the virgin PPS fibers without any presence of crystallites. After annealing, the DSC melting curves of both TA and FA PPS nonwovens exhibit endothermic annealing peaks, the origin of which is interpreted as the relaxation and devitrification of the rigid amorphous phase. However, the annealing peak position of the FA sample is always higher than that of the TA sample, which is reported for the first time. As compared with the FA sample annealed at the same temperature, TA PPS nonwovens reveal lower crystallinity and slightly larger lamellar long period (L-p) but a higher level of macroscopic fiber alignment and molecular chain orientation. These morphology and microstructure differences provide a good explanation for the superior mechanical property of TA PPS nonwovens with higher elastic modulus and tensile strength. The results are helpful in deepening the understanding of essential physical pictures of PPS nonwovens and promoting the development of the high-temperature nonwoven industry.

Preparation and properties of polyphenylene sulfide fiber

Drawing and Ultimate Tensile Properties of Modified Polyamide 6 Fibers

Effect of Heat Treatment on the Mechanical and Tribological Properties of Polyphenylene Sulfide Fiber Materials

Effect of polyphenylene sulfide sulfone sizing agent on interfacial, thermal, and mechanical properties of carbon fiber

Mechanical and Tribological Properties of Self-Reinforced Polyphenylene Sulfide Composites

Carbon fibers from polypropylene: Structural evolution of precursor fiber during stabilization and carbonization

Fabrication and characterization of polyphenylene sulfide composites with ultra-high content of carbon fiber fabrics

Effect of Carbon Nanotube on Thermal, Tribological and Mechanical Properties of 3D Printing Polyphenylene Sulfide

Preparation of High-Modulus Poly(ethylene Terephthalate) Fibers by Vibrating Hot Drawing

Bio‐based poly(trimethylene terephthalate)/polyamide 56 blend fibers via melt spinning: Preparation, structure, and properties

Morphology and Mechanical Behavior of Isotactic Polypropylene (ipp)/syndiotactic Polypropylene (spp) Blends and Fibers

Cooling rate-dependent mechanical properties of polyphenylene sulfide (PPS) and carbon fiber reinforced PPS (CF/PPS)

Effect of quercetin on the structure and oxidation resistance of polyphenylene sulfide fiber prepared by melt spinning

Heat-setting Effect on the Morphology and Phase Structures of PPS Nonwovens

Study on Structures and Properties of Ultra-Hot Drawing UHMWPE Fibers Fabricated Via Dry Spinning Method

Ultra high density carbon fiber derived from isotactic polypropylene fiber without skin‐core structure

Optimization of hot drawing process of ultra‐high molecular weight polyethylene monofilament prepared by melt spinning

The influence of formation temperatures on the crystal structure and mechanical properties of ultrahigh-molecular-weight polyethylene/high-density polyethylene-blend fibers prepared by melt spinning

Improving the Oxidation Resistance of Polyphenylene Sulfide Fibers by Doping Copper Nanoparticles Loaded Halloysite Nanotubes

Competition of memory effect and thermal degradation on the crystallization behavior of polyphenylene sulfide

Preparation of Conductive Polyester Fiber Compounded with Carbon Black