Abstract:The present work investigates the effect of vanadium (V) micro-alloying addition on the microstructural evolution and mechanical properties of Al 354.0 alloy in as-cast and T6 condition. In particular, Al 354.0 with and without 0.3 wt.% V was developed by squeeze casting technique. The as-cast ingots were subjected to two types of heat treatment schedules, i.e., solution heat treatment at 495 °C for 8 h, followed by rapid water quenching and artificial aging at 190 °C for 2 h (T6), and solution heat treatment at 515 °C for 10 h, followed by rapid water quenching and artificial aging at 210 °C for 6 h (MT6), to modify the microstructure, morphology, and distribution of Al-, Cu-, and Mg-containing secondary phase(s). The phase and microstructure of unmodified and 0.3 wt.% V-modified alloys were analyzed using x-ray diffraction, optical microscopy, and field emission scanning electron microscopy coupled with energy-dispersive x-ray spectroscopy. Detailed analyses show that Al 2 Cu/Al 2 Cu(SiMg), Al 5 Si 2 Mg, and Al 2 Si were the strengthening phases in the unmodified alloy, whereas 0.3 wt.% V-modified alloy contains Al 10 V/Al 10 V(Mg), Al 3 Cu, Mg 2 Si, Al 4 Si, and Al(SiCuMg) as the primary strengthening phase(s). A subtle increase in the mechanical properties was evident in the 0.3 wt.% V-modified alloy compared to unmodified alloy at ambient temperature due to the presence of Al 10 V/Al 10 V(Mg) fine precipitates and Al(SiCuMg) intermetallic along the grain boundaries (GBs) preventing dislocation movement. T6 treatment resulted in a grain growth where needle/plate morphology of eutectic silicon was partially converted into spheroidal morphology, and Al 2 Cu/AlSiCuMg, Mg 2 Si, and Al 10 V/Al 10 V(Mg) intermetallic phases emerged increasing the tensile (0.3% V modified vs. unmodified; YS: ~ 287 vs. ~ 268 MPa, UTS: ~ 330 vs. ~ 334 MPa, elongation: ~ 1.5% vs. ~ 2.6%), compression (0.3% V modified vs. unmodified YS: ~ 497 vs. ~ 460 MPa, UCS: ~ 790 vs. ~ 776 MPa, compressive strain: ~ 40% vs. ~ 42%), and wear properties. However, modified T6 treatment (MT6) resulted in a grain growth where needle/plate morphology of eutectic silicon converted into spheroidal morphology, and Al 2 Cu partially and Mg 2 Si precipitates along the GBs were completely dissolved in the α -Al matrix by incipient melting improving the ductility (~5.9%) at the expense of yield strength (~104 MPa) and ultimate tensile strength (~218 MPa).

STUDY ON THE MECHANICAL PROPERTY OF AgMgV ALLOYS USED IN BSCCO TAPES

Mechanical properties of several sheath silver alloys used in BSCCO tapes

Mechanical Properties Of (Bi,Pb)-2223 Multifilament Tapes With Ag-Alloy Sheath

The Microstructure and Mechanical Properties of As-cast Mg-10Gd-3Y-xZn-0.6Zr (x=0, 0.5, 1 and 2 Wt%) Alloys

Investigations on Microstructure and Mechanical Properties of Cast Mg-Gd-Y-Zn-Zr-Nd Alloy

Influence of Al Addition on the Microstructure and Mechanical Properties of Mg-Zn-Sn-Mn-Ca Alloys

Fabrication and properties of some Ag-alloy sheathed Bi-2223 tapes

Investigating the role of Cu, Zr and V on the evolution of microstructure and properties of Al-Si-Mg cast alloys

Enhanced Mechanical Properties and Isotropy of Mg-2Al-0.8Sn Alloy through Ca Addition

Effect of Vanadium Micro-alloying on the Microstructure and Mechanical Properties of Stir Cast Al 354.0 Alloy

Study on the effect of enhanced magnesium and copper contents on microstructure and property of Al-Zn-Mg-Cu alloys with high zinc element content during fabrication processes

Microstructure and Mechanical Properties of As-Aged Mg-Zn-Sn-Mn-Al Alloys

Microstructure and Properties of High Strength and High Conductivity Cu-0.4Mg Alloy Processed by Upward Continuous Casting and Multi-pass Drawing

Effect of Ca addition on microstructure and mechanical properties of Mg–3.8Al–1.1Sn alloys

Effect of Mg addition on microstructure and mechanical properties of Al-Si-Cu-Fe alloy with squeeze casting

Microstructures and Mechanical Properties of As-Cast Mg–5Al–0.4Mn–xNd (x = 0, 1, 2 and 4) Alloys

Mechanical Properties and Microstructures of Mg-Al-Zn Alloys with High Aluminum Contents

Effect of Sm content on microstructure and properties of extruded Mg-6Al-2Sr alloy

The Research of Microstructure and Mechanical Properties of Mg–7Gd–3Y–1Nd–0.5Zn–0.5Zr (wt%) Alloy

Strengthening Effect of Extruded Mg-8Sn-2Zn-2Al Alloy: Influence of Micro and Nano-Size Mg2Sn Precipitates

Simultaneous Improvement of Strength, Ductility and Damping Capacity of Single Β-Phase Mg-Li-Al-Zn Alloys