Abstract:The laser welding of dissimilar 2219 Al–Cu and 2195 Al–Li alloys is a significant attempt in the fabrication of rocket propellant tanks, aiming at the escalating demands for weight reduction and cost efficiency. The variances in microstructure evolution for 2219/2195 aluminum alloys laser welded joint deserves thorough investigation because it certainly results in the discrepancies in mechanical property In this paper, the temperature field, microstructure, element distribution, grain orientation, and texture on both sides of the laser welded joint were comprehensively investigated through a combination of simulations and experiments. The tensile strength was tested and the fracture mechanism was analyzed based on the microstructure characteristic. It is found that the wider columnar dendrites zone is generated due to the large temperature gradient from on the 2195 Al–Li alloy side. The grain orientation of the non-dendrite equiaxed zone (EQZ) and columnar grain near the fusion line are significantly influenced by the grain orientation of base metal (BM). On the one side of 2195 Al–Li alloy, the majority of grains feature diameters predominantly within the 3–6 μm range. The region in the vicinity of fusion line on one side of the 2195 Al–Li alloy has the weakest performance. It is deduced that the poor tensile property on one side of the 2195 Al–Li alloy is not only attributed to the loss of Mg and Li elements, but also owing to the evolution of texture. The rotated goss texture with high intensity is formed in EQZ near the fusion line on one side of 2219 Al–Cu alloy.

Porosity characterization in laser welds of Al-Li alloy1420

Porosity Formation and Its Effect on the Properties of Hybrid Laser Welded Al Alloy Joints

Tensile Fracture in Laser Welding Joints of Al-Cu-Li-Mg-X Alloy Bearing Gaseous Porosity

Microstructure and Mechanical Properties of Laser-Mig Hybrid Welding of 1420 AlLi Alloy

Mechanisms of the Porosity Formation During the Fiber Laser Lap Welding of Al 5754 Sheets

MECHANISMS OF THE POROSITY FORMATION DURING THE FIBER LASER LAP WELDING OF ALUMINIUM ALLOY

Porosity Sensitivity of A356 Al Alloy During Fiber Laser Welding

Laser Scanning Welding of 2060 Al-Li Alloy with Filler Wire

Structure and mechanical properties of aluminum-lithium alloy 1420 with a weld

Microstructure Evolution and Mechanical Property of Laser Welded Al-Li Alloy with Filler Strip

Porosity in fiber laser formation of 5A06 aluminum alloy

A comparative study on microstructure and properties of pulsed laser welding and continuous laser welding of Al-25Si-4Cu-Mg high silicon aluminum alloy

Laser pressure welding of Al-Li alloy 2198: effect of welding parameters on fusion zone characteristics associated with mechanical properties

Unravelling Asymmetrical Microstructure Evolution and Tensile Fracture Mechanism in Laser Welding of Dissimilar 2219/2195 Aluminum Alloys

Influence of surface pretreatment on porosity and microstructure of laser welding in AlSi10Mg alloys sheets fabricated by laser powder bed fusion

Microstructural and Mechanical Characterization of Aluminum-Lithium Alloy 2060 Welded by Fiber Laser

Microstructural, Porosity and Mechanical Properties of Lap Joint Laser Welding for 5182 and 6061 Dissimilar Aluminum Alloys under Different Place Configurations

Effect of Porosity Morphology and Elements Characteristics on Mechanical Property in T-joints During Dual Laser-Beam Bilateral Synchronous Welding of 2060/2099 Al-Li Alloys

Effect of swinging laser on porosity, microstructure, and mechanical properties of laser welded aluminum alloy joints with different lap forms

Microstructural Inhomogeneity in the Fusion Zone of Laser Welds

Microstructure and Properties Analysis of Laser Welding and Laser Weld Bonding Mg to Al Joints