Abstract:It is common knowledge that one of the main issues of hypersonic flight is the thermal management of the overall vehicle and more specifically the cooling of the engine, since even composite materials can't withstand the large heat load found in a Scramjet combustion chamber. The other critical point is that mixing and combustion should be sufficiently fast in order to avoid long combustion chamber caused by supersonic internal flow and short residence time. This dual requirement leads to the idea of using inboard fuel as coolant, in order to limit the weight of the cooling system and to benefit from some fuel endothermic capability, i.e. the capability of heavy hydrocarbon fuels to decompose into lighter species, mainly methane, ethane, hydrogen and alkenes from C2 to C10, providing welcomed additional heat sink. Analytical (such as NANCY code) and multidimensional tools (such as CFD-ACE), extensively used for design and analysis of metallic and composite cooled structures are also very efficient to address hydraulic and thermal phenomenon, but, up to now, these approaches did not compute the chemical decomposition of the fuel, except by the way of assumed thermo -dynamical properties. Due to the large number of components found in a traditional jet fuel, the characterization of the thermal decomposition of such products is not a simple issue. In order to obtain a good understanding of the various phenomenon inside a cooled panel of a Scramjet, we selected n-dodecane as a representative surrogate for envisioned endothermic fuel. The thermal decomposition model for n-dodecane was developed by the DCPR and validated thanks to available experimental data. This model, written in a CHEMKIN II format, has been proved able to describe the behavior of n-dodecane between 600 1100 K and 110 bar and could certainly be extrapolated in a wider temperature and pressure range, without taking specifically into account the supercritical phase. This paper will present some numerical results obtained for a cooled composite panel under different heat loads, from a physical point of view (temperature of the panel) and a chemical point of view (composition of the decomposed fuel). INTRODUCTION In a large part of the flight regime, the air-breathing mode appears to be a good solution for future Reusable Space Launchers (RSL). Dual-mode ramjets have been studied to propel such TSTO (Two-Stage To Orbit) or Single -Stage To Orbit (SSTO) vehicles. For example, in the scope of the French PREPHA program, the study of a generic SSTO vehicle led the conclusion that the best type of air-breathing engine could be the Dual-Mode Ramjet (DMR, with subsonic then s upersonic combustion). Airbreathing launchers could typically use hydrogen-fuelled DMR. Less energetic fuels like hydrocarbons could also be used at a Mach number of flight lower than 8, to take advantage of their higher density. In this case, the engine must be able to manage two different fuels. DMR or scramjets designed for hypersonic military applications are typically associated with liquid hydrocarbons and with a maximum flight Mach number of 8 (missiles). Given the very high heat load inside the combustion chamber, active cooling seems to be the only way for a proper thermal management of the engine (Figure 1).

Performance Cycle Analysis of an Open Cooling Cycle for a Scramjet

Conceptual Design and Optimization of Scramjet Engines Using the Exergy Method

Thermodynamic analysis on the performance of hydrocarbon fueled scramjet with inlet active cooling

A review of regenerative cooling technologies for scramjets

Progress of Coupled Heat Transfer Mechanisms of Regenerative Cooling System in a Scramjet

Feasibility and performance evaluation of film cooling using incoming air in a gel-fueled scramjet

Performance Analysis and Dynamic Optimization of Integrated Cooling and Power Generation System Based on Supercritical CO2 Cycle for Turbine-Based Combined Cycle Engine

Numerical investigation on regeneration-transpiration combined cooling of cavity structure in scramjet engine

A Novel Fuel-Based CO2 Transcritical Cycle for Combined Cooling and Power Generation on Hypersonic Aircrafts

Thermodynamic Analysis of the Second Fluid Brayton Cycle for Scramjet Engine

On compression level of hypersonic airflow in high-mach scramjet

Computational Study of Heat Exchange and Thermal Oxidative Coking of Supercritical-Pressure Kerosene with Compressed Air in Counterflows

Thermodynamic analysis for a novel chemical precooling turbojet engine based on a multi-stage precooling-compression cycle

Insight into jet-regeneration composite cooling technology employed in scramjet: Significance of relative positions of two jet holes

CONTRIBUTION TO SCRAMJET ACTIVE COOLING ANALYSIS USING N-DODECANE DECOMPOSITION MODEL AS A GENERIC ENDOTHERMIC FUEL

Thermal performance evaluation of a distributed regenerative cooling system using supercritical catalytic steam reforming of aviation kerosene for scramjet engine

Design optimization and off-design performance analysis of one-dimensional supercritical CO 2 Brayton cycle

Numerical Investigation of the Intercooler Performance of Aircraft Piston Engines under the Influence of High Altitude and Cruise Mode

Modeling and Performance Analysis of a Pre-Cooling and Power Generation System Based on the Supercritical CO2 Brayton Cycle on Turbine-Based Combined Cycle Engines

Scramjet performance for ideal combustion processes

EFFECTS OF COOLING SCHEMES ON THE PERFORMANCE OF SPACE CLOSED BRAYTON CYCLE